ASTM C507M-10
(Specification)Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
ABSTRACT
This specification covers reinforced elliptically shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts. Pipe design based on its major axis shall be designated as horizontal and vertical elliptical pipe. The reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in which steel has been embedded in such a manner that the steel and concrete act together. The combination of cementitious materials used in the concrete shall only be one of the following: Portland cement, Portland blast furnace slag cement, slag modified Portland cement, Portland pozzolan cement, a combination of Portland cement and ground granulated blast-furnace slag, a combination of Portland cement and fly ash, a combination of Portland cement, ground granulated blast-furnace slag, and fly ash. Collated fibrillated virgin polypropylene fibers may be used. Design of pipe such as size, shape, special designs, and area, shall be as listed in the specification. Circumferential, longitudinal, and joint reinforcements shall meet the requirements of this specification. Mixture and curing of pipe shall conform to the requirements of this specification. Compression tests determining concrete compressive strength may be made on either standard rodded concrete cylinders or concrete cylinders compacted and cured in like manner as the pipe, or on cores drilled from the pipe. Pipe may be repaired because of imperfections in manufacture or damage during handling and shall be acceptable if the repaired pipe conforms to the requirements of this specification.
SCOPE
1.1 This specification covers reinforced elliptically shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts.
1.2 Pipe designed for placement with the major axis horizontal shall be designated as “Horizontal Elliptical Pipe.” Pipe designed for placement with the major axis vertical shall be designated as “Vertical Elliptical Pipe.”
1.3 This specification is the SI companion to Specification C507.
Note 1—This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
Designation: C507M – 10
Standard Specification for
Reinforced Concrete Elliptical Culvert, Storm Drain, and
1
Sewer Pipe (Metric)
This standard is issued under the fixed designation C507M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope A497/A497M Specification for Steel Welded Wire Rein-
forcement, Deformed, for Concrete
1.1 This specification covers reinforced elliptically shaped
A615/A615M Specification for Deformed and Plain
concrete pipe to be used for the conveyance of sewage,
Carbon-Steel Bars for Concrete Reinforcement
industrial wastes, storm water, and for the construction of
A706/A706M Specification for Low-Alloy Steel Deformed
culverts.
and Plain Bars for Concrete Reinforcement
1.2 Pipe designed for placement with the major axis hori-
C33 Specification for Concrete Aggregates
zontal shall be designated as “Horizontal Elliptical Pipe.” Pipe
C150 Specification for Portland Cement
designed for placement with the major axis vertical shall be
C260 Specification for Air-Entraining Admixtures for Con-
designated as “Vertical Elliptical Pipe.”
crete
1.3 This specification is the SI companion to Specification
C309 Specification for Liquid Membrane-Forming Com-
C507.
pounds for Curing Concrete
NOTE 1—This specification is a manufacturing and purchase specifica-
C494/C494M Specification for Chemical Admixtures for
tion only, and does not include requirements for bedding, backfill, or the
Concrete
relationship between field load condition and the strength classification of
C497M Test Methods for Concrete Pipe, Manhole Sections,
pipe. However, experience has shown that the successful performance of
or Tile [Metric]
this product depends upon the proper selection of the class of pipe, type
of bedding and backfill, and care that the installation conforms to C595 Specification for Blended Hydraulic Cements
construction specifications. The owner of the reinforced concrete pipe
C618 Specification for Coal Fly Ash and Raw or Calcined
specified herein is cautioned that he must correlate the field requirements
Natural Pozzolan for Use in Concrete
with the class of pipe specified and provide inspection at the construction
C822 Terminology Relating to Concrete Pipe and Related
site.
Products
C989 Specification for Slag Cement for Use in Concrete
2. Referenced Documents
and Mortars
2
2.1 ASTM Standards:
C1017/C1017M Specification for ChemicalAdmixtures for
A36/A36M Specification for Carbon Structural Steel
Use in Producing Flowing Concrete
A82/A82M Specification for SteelWire, Plain, for Concrete
C1116 Specification for Fiber-Reinforced Concrete and
Reinforcement
Shotcrete
A185/A185M Specification for Steel Welded Wire Rein-
forcement, Plain, for Concrete
3. Terminology
A496/A496M Specification for Steel Wire, Deformed, for
3.1 Definitions—For definitions of terms relating to con-
Concrete Reinforcement
crete pipe, see Terminology C822.
4. Classification
1
This specification is under the jurisdiction of ASTM Committee C13 on 4.1 Pipe manufactured according to this specification shall
Concrete Pipe and is the direct responsibility of Subcommittee C13.02 on
be of five classes each for horizontal elliptical and vertical
Reinforced Sewer and Culvert Pipe.
elliptical pipe with identification as follows:
Current edition approved Feb. 1, 2010. Published February 2010. Originally
Horizontal Elliptical Pipe Vertical Elliptical Pipe
approved in 1980. Last previous edition approved in 2009 as C507M – 09. DOI:
Class HE-A Class VE-II
10.1520/C0507M-10.
2
Class HE-I Class VE-III
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Class HE-II Class VE-IV
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Class HE-III Class VE-V
Standards volume information, refer to the standard’s Document Summary page on
Class HE-IV Class VE-VI
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Please contact ASTM International (www.astm.org) for the latest information.
C507M – 10
4.2 The strength requirements for horizontal elliptical pipe inspection of the finished pipe to determine its conformance
are prescribed in Table 1 and for vertical elliptical pipe are with the accepted design prescribed and its freedom from
prescribed in Table 2.
defects.
5.1.2 Acceptance on the Basis of Material Test and Inspec-
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C507M–09 Designation: C507M – 10
Standard Specification for
Reinforced Concrete Elliptical Culvert, Storm Drain, and
1
Sewer Pipe (Metric)
This standard is issued under the fixed designation C507M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers reinforced elliptically shaped concrete pipe to be used for the conveyance of sewage, industrial
wastes, storm water, and for the construction of culverts.
1.2 Pipedesignedforplacementwiththemajoraxishorizontalshallbedesignatedas“HorizontalEllipticalPipe.”Pipedesigned
for placement with the major axis vertical shall be designated as “Vertical Elliptical Pipe.”
1.3 This specification is the SI companion to Specification C507.
NOTE 1—This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the
relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this
product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to construction
specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe
specified and provide inspection at the construction site.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement
A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete
A496/A496M Specification for Steel Wire, Deformed, for Concrete Reinforcement
A497/A497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
C33 Specification for Concrete Aggregates
C150 Specification for Portland Cement
C260 Specification for Air-Entraining Admixtures for Concrete
C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C497M Test Methods for Concrete Pipe, Manhole Sections, or Tile [Metric]
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C822 Terminology Relating to Concrete Pipe and Related Products
C989 Specification for Slag Cement for Use in Concrete and Mortars
C1017/C1017M Specification for Chemical Admixtures for Use in Producing Flowing Concrete
C1116 Specification for Fiber-Reinforced Concrete and Shotcrete
3. Terminology
3.1 Definitions—For definitions of terms relating to concrete pipe, see Terminology C822.
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.02 on Reinforced Sewer
and Culvert Pipe.
Current edition approved JuneFeb. 1, 2009.2010. Published June 2009.February 2010. Originally approved in 1980. Last previous edition approved in 20082009 as
C507M–08a.C507M – 09. DOI: 10.1520/C0507M-109.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C507M – 10
4. Classification
4.1 Pipe manufactured according to this specification shall be of five classes each for horizontal elliptical and vertical elliptical
pipe with identification as follows:
Horizontal Elliptical Pipe Vertical Elliptical Pipe
Class HE-A Class VE-II
Class HE-I Class VE-III
Class HE-II Class VE-IV
Class HE-III Class VE-V
Class HE-IV Class VE-VI
4.2 ThestrengthrequirementsforhorizontalellipticalpipeareprescribedinTable1andforverticalellipticalpipeareprescribed
in Table 2.
5. Basis of Acceptance
5.1 Unless otherwise designated by the owner at the tim
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.