iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6461-99(2007)e2

(Specification)

Standard Specification for Silt Fence Materials (Withdrawn 2016)

Standard Specification for Silt Fence Materials (Withdrawn 2016)

ABSTRACT
This specification covers requirements and test methods for geotextile fabrics and associated components used in temporary silt fence applications. It is applicable to the use of a geotextile as a vertical permeable interceptor designed to remove suspended soil from overland, nonconcentrated water flow. The function of a temporary silt fence is to trap and allow settlement of soil particles from sediment laden water. The purpose is to greatly limit the transport of eroded soil from the construction site by water runoff. Fibers used in the manufacture of geotextiles for silt fence, and the threads used in joining geotextiles by sewing, shall consist of long-chain synthetic polymers composed of at least 95 % by weight of polyolefins or polyester. They shall be formed into a stable network such that the filaments or yarns retain their dimensional stability relative to each other, including selvages. Geotextiles and related materials used for temporary silt fence shall conform with required grab strength, permittivity, apparent opening size, and ultraviolet stability. The prescribed support posts are described in the specification.
SCOPE
1.1 This specification covers requirements and test methods for geotextile fabrics and associated components used in temporary silt fence applications. This is a material purchasing specification based on AASHTO M288.
1.2 This specification is applicable to the use of a geotextile as a vertical permeable interceptor designed to remove suspended soil from overland, nonconcentrated water flow. The function of a temporary silt fence is to trap and allow settlement of soil particles from sediment laden water. The purpose is to greatly limit the transport of eroded soil from the a construction site by water runoff.
1.3 The tests used to characterize the silt fence are intended to ensure good workmanship and quality and are not necessarily adequate for design purposes in view of the wide variety of possible sediments and performance objectives.
1.4 The values stated in SI units are to be regarded as the standard. The values in inch-pound units are provided for information only.
WITHDRAWN RATIONALE
This specification covers requirements and test methods for geotextile fabrics and associated components used in temporary silt fence applications. This is a material purchasing specification based on AASHTO M288.
Formerly under the jurisdiction of Committee D18 on Soil and Rock, this specification was withdrawn in February 2016 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
31-Oct-2007
Withdrawal Date
16-Feb-2016
ICS
59.080.70 - Geotextiles
Technical Committee
D18 - Soil and Rock
Drafting Committee
D18.25 - Erosion and Sediment Control Technology
Current Stage
Ref Project

Relations

Replaces
ASTM D6461-99(2007)e1 - Standard Specification for Silt Fence Materials
Effective Date
01-Nov-2007
Replaced By
ASTM D6461/D6461M-16 - Standard Specification for Silt Fence Materials
Effective Date
01-Jul-2016

Buy Standard

ASTM D6461-99(2007)e2 - Standard Specification for Silt Fence Materials (Withdrawn 2016)ASTM D6461-99(2007)e2 - Standard Specification for Silt Fence Materials (Withdrawn 2016)
PreviousNext
Technical specification
ASTM D6461-99(2007)e2 - Standard Specification for Silt Fence Materials (Withdrawn 2016)
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´2
Designation:D6461 −99(Reapproved 2007)
Standard Specification for
Silt Fence Materials
This standard is issued under the fixed designation D6461; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
´ NOTE—Editorial changes were made throughout in November 2007.
´ NOTE—Reference to Terminology D653 added in March 2008.
1. Scope D4439 Terminology for Geosynthetics
D4491 Test Methods for Water Permeability of Geotextiles
1.1 This specification covers requirements and test methods
by Permittivity
for geotextile fabrics and associated components used in
D4632 Test Method for Grab Breaking Load and Elongation
temporary silt fence applications. This is a material purchasing
of Geotextiles
specification based on AASHTO M288.
D4751 Test Method for DeterminingApparent Opening Size
1.2 This specification is applicable to the use of a geotextile
of a Geotextile
as a vertical permeable interceptor designed to remove sus-
D4759 Practice for Determining the Specification Confor-
pended soil from overland, nonconcentrated water flow. The
mance of Geosynthetics
function of a temporary silt fence is to trap and allow
D4873 Guide for Identification, Storage, and Handling of
settlement of soil particles from sediment laden water. The
Geosynthetic Rolls and Samples
purpose is to greatly limit the transport of eroded soil from the
D5141 TestMethodforDeterminingFilteringEfficiencyand
a construction site by water runoff.
Flow Rate of the Filtration Component of a Sediment
Retention Device
1.3 The tests used to characterize the silt fence are intended
to ensure good workmanship and quality and are not necessar-
2.2 AASHTO Standard:
ily adequate for design purposes in view of the wide variety of
M288-96 Standard Specification for Geotextile Specifica-
possible sediments and performance objectives.
tion for Highway Applications
1.4 The values stated in SI units are to be regarded as the
3. Materials and Manufacture
standard. The values in inch-pound units are provided for
information only.
3.1 Fibers used in the manufacture of geotextiles for silt
fence, and the threads used in joining geotextiles by sewing,
2. Referenced Documents
shall consist of long-chain synthetic polymers composed of at
least 95 % by weight of polyolefins or polyester. They shall be
2.1 ASTM Standards:
formed into a stable network such that the filaments or yarns
D123 Terminology Relating to Textiles
retain their dimensional stability relative to each other, includ-
D276 Test Methods for Identification of Fibers in Textiles
ing selvages.
D653 Terminology Relating to Soil, Rock, and Contained
Fluids
3.2 Geotextiles and related materials used for temporary silt
D4354 Practice for Sampling of Geosynthetics for Testing
fence shall conform with the physical requirements of Sections
D4355 Test Method for Deterioration of Geotextiles by
7 and 8.
Exposure to Light, Moisture and Heat in a Xenon Arc
3.3 All property values, with the exception of apparent
Type Apparatus
opening size (AOS), in this specification represent minimum
average roll values (MARV) in the weakest principle direction
(that is, average test results of any roll in a lot sampled for
This specification is under the jurisdiction of ASTM Committee D18 on Soil
conformance or quality assurance testing shall meet or exceed
and Rock and is the direct responsibility of Subcommittee D18.25 on Erosion and
theminimumvalueprovidedherein).ValuesforAOSrepresent
Sediment Control Technology.
Current edition approved Nov. 1, 2007. Published November 2007. Originally
maximum average roll values.
approved in 1999. Last previous edition approved in 1999 as D6461 – 99. DOI:
10.1520/D6461-99R07E02.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from American Association of State Highway and Transportation
Standards volume information, refer to the standard’s Document Summary page on Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
the ASTM website. http://www.transportation.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
´2
D6461−99 (2007)
4. Sampling, Testing, and Acceptance 6. Shipment and Storage
4.1 Silt fence shall be subject to sampling and testing to
6.1 Silt fence labeling, shipment and storage shall follow
verify conformance with this specification. Sampling for test-
Guide D4873. Product labels shall clearly show the manufac-
ing shall be in accordance with Practice D4354. Acceptance
turer or supplier name, style name, and roll number. Each
shall be based on testing of either conformance samples
shipping document shall include a notation certifying that the
obtained using Procedure A of Practice D4354, or based on
material is in accordance with the manufacturer’s certificate.
manufacturer’s certifications and testing of quality assurance
6.2 Each silt fence roll shall be wrapped with a material that
samples obtained using Procedure B of Practice D4354. A lot
willprotectthegeotextilefromdamageduetoshipment,water,
size for conformance or quality assurance sampling shall be
sunlight, and contaminants. The protective wrapping shall be
considered to be the shipment quantity of the given product or
maintained during periods of shipment and storage.
a truckload of the given product, whichever is smaller.
4.2 Testing shall be performed in accordance with the test 6.3 During storage, silt fence rolls shall be elevated off the
methods referenced in this specification for the indicated
ground and adequately covered to protect them from the
application. The number of specimens to test per sample (see
following—site construction damage, precipitation, extended
Terminology D653) is specifi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6462-19(Practice)
Standard Practice for Silt Fence Installation and Maintenance

SIGNIFICANCE AND USE
4.1 Proper installation is critical to effective performance of silt fence. This practice presents procedures for installing and maintaining silt fence that have been shown to result in silt fence installations that effectively redirect and impound surface runoff and, thereby, provide effective sediment control.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors
SCOPE
1.1 This practice covers common installation and maintenance procedures for temporary silt fence applications. This practice is based on AASHTO M288.  
1.2 This practice is applicable to the use of silt fence as a vertical permeable interceptor designed to remove suspended soil from overland, non-concentrated water flow. The function of a temporary silt fence is to trap and allow settlement of soil particles from sediment laden water by intercepting and impounding water in an effort to slow the transport velocity and provide storage for sediment to be captured. The purpose is to greatly limit the transport of eroded soil from the construction site by water runoff.  
1.3 The practices presented herein are intended to ensure good workmanship and quality, but do not necessarily apply to the concentrated flow applications.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents, therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This practice offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8198-18(Specification)
Standard Specification for Hydraulically Applied 100 % Wood Fiber Mulches

SCOPE
1.1 This specification covers the physical properties and testing requirements for 100 % wood fiber Hydraulic Erosion Control Products (HECP) mulches.  
1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units, which are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard. The sieve designations are identified using the “alternative” system in accordance with Practice E11, such as 3-in. and No. 200, instead of the “standard” of 75-mm and 75-µm, respectively.  
1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.  
1.3.1 The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7007-24(Practice)
Standard Practices for Electrical Methods for Locating Leaks in Geomembranes Covered with Water or Earthen Materials

SIGNIFICANCE AND USE
4.1 Geomembranes are used as impermeable barriers to prevent liquids from leaking from landfills, ponds, and other containments. The liquids may contain contaminants that, if released, can cause damage to the environment. Leaking liquids can erode the subgrade, causing further damage. Leakage can result in product loss or otherwise prevent the installation from performing its intended containment purpose. For these reasons, it is desirable that the geomembrane have as little leakage as practical.  
4.2 Geomembrane leaks can be caused by poor quality of the subgrade, poor quality of the material placed on the geomembrane, accidents, poor workmanship, manufacturing defects, and carelessness.  
4.3 The most significant causes of leaks in geomembranes that are covered with only water are related to construction activities, including pumps and equipment placed on the geomembrane, accidental punctures, and punctures caused by traffic over rocks or debris on the geomembrane or in the subgrade.  
4.4 The most significant cause of leaks in geomembranes covered with earthen materials is construction damage caused by machinery that occurs while placing the earthen material on the geomembrane. Such damage also can breach additional layers of the lining system such as geosynthetic clay liners.  
4.5 Electrical leak location methods are an effective final quality assurance measure to detect and locate leaks. If any of the requirements for survey area preparation is not adhered to, then leak sensitivity could be diminished. Optimal survey area conditions are described in Section 6.
SCOPE
1.1 These practices cover standard procedures for using electrical methods to locate leaks in geomembranes covered with water or earthen materials. For clarity, this practice uses the term “leak” to mean holes, punctures, tears, knife cuts, seam defects, cracks, and similar breaches in an installed geomembrane (as defined in 3.2.9).  
1.2 These practices are intended to ensure that leak location surveys are performed with a standardized level of leak detection capability. To allow further innovations, and because various leak location practitioners use a wide variety of procedures and equipment to perform these surveys, performance-based protocol are also used that specify minimum leak detection criteria.  
1.3 The survey shall then be conducted using the demonstrated equipment, procedures, and survey parameters. In the absence of the minimum signal strength during leak detection distance testing, a minimum measurement density specification is provided. Alternatively, the minimum measurement density may simply be used.  
1.4 Separate procedures are given for leak location surveys for geomembranes covered with water and for geomembranes covered with earthen materials. Separate procedures are given for leak detection distance tests using actual and artificial leaks.  
1.5 Examples of methods of data analysis for soil-covered surveys are provided as guidance in Appendix X1.  
1.6 Leak location surveys can be used on geomembranes installed in basins, ponds, tanks, ore and waste pads, landfill cells, landfill caps, and other containment facilities. The procedures are applicable for geomembranes made of materials such as polyethylene, polypropylene, polyvinyl chloride, chlorosulfonated polyethylene, bituminous material, and other electrically insulating materials.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 (Warning—The electrical methods used for geomembrane leak location could use high voltages, resulting in the potential for electrical shock or electrocution. This hazard might be increased because operations might be conducted in or near water. In particular, a high voltage could exist between the water or earthen material and earth ground, or any grounded conductor. These procedures are potentially VERY DANGEROUS, and can re...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM D7005/D7005M-16(2024)(Test Method)
Standard Test Method for Determining the Bond Strength (Ply Adhesion) of Geocomposites

SIGNIFICANCE AND USE
5.1 This test method is to be used as a quality control or quality assurance test. As a manufacturing quality control (MQC) test, it would generally be used by the geocomposite product manufacturer or fabricator. As a construction quality assurance (CQA) test, it would be used by certification or inspection organizations.  
5.2 This test method can also be used to verify if the adhesion or bond strength varies after exposure to various incubation media in durability or chemical resistance testing, or both.  
5.3 Whatever use is to be associated with the test, it should be understood that this is an index test.
Note 2: There have been numerous attempts to relate the results of this test to the interface shearing resistance of the respective materials determined per Test Method D5321/D5321M. To date, no relationships have been established between the two properties.  
5.4 Test Method D7005/D7005M for determining the bond strength (ply adhesion) strength may be used as an acceptance test of commercial shipments of geocomposites, but caution is advised since information about between-laboratory precision is incomplete. Comparative tests as directed in 5.4.1 are advisable.  
5.4.1 In the case of a dispute arising from differences in reported test results when using the procedure in Test Method D7005/D7005M for acceptance of commercial shipments, the purchaser and the supplier should first confirm that the tests were conducted using comparable test parameters including specimen conditioning, grip faces, grip size, etc. Comparative tests should then be conducted to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of the material in question. The test specimens should be randomly assigned to each laboratory for testing. The average results from ...
SCOPE
1.1 It has been widely discussed in the literature that bond strength of flexible multi-ply materials is difficult to measure with current technology. The above is recognized and accepted, since all known methods of measurement include the force required to bend the separated layers, in addition to that required to separate them. However, useful information can be obtained when one realizes that the bending force is included and that direct comparison between different materials, or even between the same materials of different thickness, cannot be made. Also, conditioning that affects the moduli of the plies will be reflected in the bond strength measurement.  
1.2 This index test method defines a procedure for comparing the bond strength or ply adhesion of geocomposites. The focus is on geotextiles bonded to geonets or other types of drainage cores, for example, geomats, geospacers, etc. Other possible uses are geotextiles adhered or bonded to themselves, geomembranes, geogrids, or other dissimilar materials. Various processes can make such laminates: adhesives, thermal bonding, stitch bonding, needling, spread coating, etc.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 11.1.1.  
1.5 This international standard was developed in accordance with internationally recognized principles on ...

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4439-24(Terminology)
Standard Terminology for Geosynthetics
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4595/D4595M-24(Test Method)
Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Method

SIGNIFICANCE AND USE
5.1 The determination of the wide-width force-elongation properties of geotextiles provides design parameters for reinforcement type applications, for example, design of reinforced roadways/pavements, reinforced embankments over soft subgrades, reinforced soil retaining walls, and reinforcement of slopes. When strength is not necessarily a design consideration, an alternative test method may be used for acceptance testing. Test Method D4595/D4595M for the determination of the wide-width tensile properties of geotextiles may be used for the acceptance testing of commercial shipments of geotextiles, but caution is advised since information about between-laboratory precision is incomplete (Note 3). Comparative tests as directed in 5.1.1 may be advisable.  
5.1.1 In cases of a dispute arising from differences in reported test results when using Test Method D4595/D4595M for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. At a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing began. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in light of the known bias.  
5.2 Most geotextiles can be tested by this test method. Some modification of clamping techniques may be necessary for a given geotextile depending upon its structure. Special clamping adaptions may be necessary with strong...
SCOPE
1.1 This test method covers the measurement of tensile properties of geotextiles using a wide-width specimen tensile method. This test method is applicable to most geotextiles that include woven geotextiles, nonwoven geotextiles, layered fabrics, and knit fabrics that are used for geotextile applications.  
1.2 This test method covers the measurement of tensile strength and elongation of geotextiles and includes directions for the calculation of initial modulus, offset modulus, secant modulus, and breaking toughness.  
1.3 Procedures for measuring the tensile properties of both conditioned and wet geotextiles by the wide-width method are included.  
1.4 The basic distinction between this test method and other methods for measuring strip tensile properties is the width of the specimen. Some fabrics used in geotextile applications have a tendency to contract (neck down) under a force in the gage length area. The greater width of the specimen specified in this test method minimizes the contraction effect of those fabrics and provides a closer relationship to expected geotextile behavior in the field and a standard comparison.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Developme...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D6637/D6637M-15(2023)(Test Method)
Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method

SIGNIFICANCE AND USE
5.1 The determination of the tensile force-elongation values of geogrids provides index property values. This test method shall be used for quality control and acceptance testing of commercial shipments of geogrids.  
5.2 In cases of dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing began. If a bias is found, either its cause must be found and corrected or the purchaser and supplier must agree to interpret future test results in light of the known bias.  
5.3 All geogrids can be tested by any of these methods. Some modification of techniques may be necessary for a given geogrid depending upon its physical makeup. Special adaptations may be necessary with strong geogrids, multiple layered geogrids, or geogrids that tend to slip in the clamps or those which tend to be damaged by the clamps.
SCOPE
1.1 This test method covers the determination of the tensile strength properties of geogrids by subjecting strips of varying width to tensile loading.  
1.2 Three alternative procedures are provided to determine the tensile strength, as follows:  
1.2.1 Method A—Testing a single geogrid rib in tension (N or lbf).  
1.2.2 Method B—Testing multiple geogrid ribs in tension (kN/m or lbf/ft).  
1.2.3 Method C—Testing multiple layers of multiple geogrid ribs in tension (kN/m or lbf/ft).  
1.3 This test method is intended for quality control and conformance testing of geogrids.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D7747/D7747M-11(2023)(Test Method)
Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Strip Tensile Method

SIGNIFICANCE AND USE
4.1 The use of reinforced geomembranes as barrier materials has created a need for a standard test method to evaluate the quality of seams produced by thermo-fusion methods. This test method is used for quality control purposes and is intended to provide quality control and quality assurance personnel with data to evaluate seam quality.  
4.2 This standard arose from the need for a destructive test method for evaluating seams of reinforced geomembranes. Standards written for destructive testing of nonreinforced geomembranes do not include all break codes (Fig. 1) applicable to reinforced geomembranes.
FIG. 1 Break Codes for Dual Hot Wedge and Hot Air Seams of Reinforced Geomembranes Tested for Seam Strength in Shear and Peel Modes  
4.3 When reinforcement occurs in directions other than machine and cross-machine, scrim are cut at specimen edges, generally lowering results. To partially compensate for this, testing can be performed according to Test Method D7749 or the 2 in. wide strip specimen specified in this method can be utilized. Testing of 1 in. and 2 in. specimens is Method A and Method B, respectively.  
4.4 The shear test outlined in this method correlates to strength of parent material measured according to Test Method D7003/D7003M only if reinforcement is parallel to TD. For other materials, seam strength and parent material strength can be compared through Test Methods D7749 and D7004/D7004M. Values obtained with the strip methods shall not be compared to values obtained with grab methods.
SCOPE
1.1 This test method describes destructive quality control tests used to determine the integrity of thermo-fusion seams made with reinforced geomembranes. Test procedures are described for seam tests for peel and shear properties using strip specimens.  
1.2 The types of thermal field and factory seaming techniques used to construct geomembrane seams include the following:  
1.2.1 Hot Air—This technique introduces high-temperature air between two geomembrane surfaces to facilitate melting. Pressure is applied to the top or bottom geomembrane, forcing together the two surfaces to form a continuous bond.  
1.2.2 Hot Wedge—This technique melts the two geomembrane surfaces to be seamed by running a hot metal wedge between them. Pressure is applied to the top and bottom geomembrane to form a continuous bond. Some seams of this kind are made with dual tracks separated by a non-bonded gap. These seams are sometimes referred to as dual hot wedge seams or double-track seams.  
1.2.3 Extrusion—This technique encompasses extruding molten resin between two geomembranes or at the edge of two overlapped geomembranes to effect a continuous bond.  
1.2.4 Radio Frequency (RF) or Dielectric—High-frequency dielectric equipment is used to generate heat and pressure to form an overlap seam in factory fabrication.  
1.2.5 Impulse—Clamping bars heated by wires or a ribbon melt the sheets clamped between them. A cooling period while still clamped allows the polymer to solidify before being released.  
1.3 The types of materials covered by this test method include, but are not limited to, reinforced geomembranes made from the following polymers:  
1.3.1 Very low-density polyethylene (VLDPE).  
1.3.2 Linear low-density polyethylene (LLDPE).  
1.3.3 Flexible polypropylene (fPP).  
1.3.4 Polyvinyl chloride (PVC).  
1.3.5 Chlorosulfonated polyethylene (CSPE).  
1.3.6 Ethylene interpolymer alloy (EIA).  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish ap...

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5820-95(2023)(Practice)
Standard Practice for Pressurized Air Channel Evaluation of Dual-Seamed Geomembranes

SIGNIFICANCE AND USE
5.1 The increased use of geomembranes as barrier materials to restrict liquid or gas movement, and the common use of dual-track seams in joining these sheets, has created a need for a standard nondestructive test by which the quality of the seams can be assessed for continuity and watertightness. The test is not intended to provide any indication of the physical strength of the seam.  
5.2 This practice recommends an air pressure test within the channel created between dual-seamed tracks whereby the presence of unbonded sections or channels, voids, nonhomogenities, discontinuities, foreign objects, and the like, in the seamed region can be identified.  
5.3 This technique is intended for use on seams between geomembrane sheets formulated from the appropriate polymers and compounding ingredients to form a plastic or elastomer sheet material that meets all specified requirements for the end use of the product.
SCOPE
1.1 This practice covers a nondestructive evaluation of the continuity of parallel geomembrane seams separated by an unwelded air channel. The unwelded air channel between the two distinct seamed regions is sealed and inflated with air to a predetermined pressure. Long lengths of seam can be evaluated by this practice more quickly than by other common nondestructive tests.  
1.2 This practice should not be used as a substitute for destructive testing. Used in conjunction with destructive testing, this method can provide additional information regarding the seams undergoing testing.  
1.3 This practice supercedes Practice D4437/D4437M for geomembrane seams that include an air channel. Practice D4437/D4437M may continue to be used for other types of seams. The user is referred to the referenced standards or to EPA/530/SW-91/051 for additional information regarding geomembrane seaming techniques and construction quality assurance.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5101-23(Test Method)
Standard Test Method for Measuring the Filtration Compatibility of Soil-Geotextile Systems

SIGNIFICANCE AND USE
5.1 This test method is recommended for the evaluation of the performance of water-saturated soil-geotextile systems under unidirectional flow conditions. The results obtained may be used as an indication of the compatibility of the soil-geotextile system with respect to both particle retention and flow capacity.  
5.2 This test method is intended to evaluate the performance of specific on-site soils and geotextiles at the design stage of a project, or to provide qualitative data that may help identify causes of failure (for example, clogging, particle loss). It is not appropriate for acceptance testing of geotextiles. It is also improper to utilize the results from this test for job specifications or manufacturers' certifications.  
5.3 This test method is intended for site-specific investigation therefore is not an index property of the geotextile, and thus is not intended to be requested of the manufacturer or supplier of the geotextile.
SCOPE
1.1 This test method covers performance tests applicable for determining the compatibility of geotextiles with various types of water-saturated soils under unidirectional flow conditions.  
1.2 Two evaluation methods may be used to investigate soil-geotextile filtration behavior, depending on the soil type:  
1.2.1 For soils with a plasticity index lower than 5, the systems compatibility shall be evaluated per this standard.  
1.2.2 For soils with a plasticity index of 5 or more, it is recommended to use Test Method D5567 (‘HCR,’ Hydraulic Conductivity Ratio) instead of this test method.  
1.2.3 If the plasticity index of the soil is close to 5, the involved parties shall agree on the selection of the appropriate method prior to conducting the test. This task may require comparison of the permeability of the soil-geotextile system to the detection limits of the HCR and Gradient Ratio Test (GRT) test apparatus being used.  
1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off