ASTM E1035-18(2023)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E1035 − 18 (Reapproved 2023)
Standard Practice for
Determining Neutron Exposures for Nuclear Reactor Vessel
Support Structures
This standard is issued under the fixed designation E1035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This practice covers procedures for monitoring the
E170 Terminology Relating to Radiation Measurements and
neutron radiation exposures experienced by ferritic materials in
Dosimetry
nuclear reactor vessel support structures located in the vicinity
E482 Guide for Application of Neutron Transport Methods
of the active core. This practice includes guidelines for:
for Reactor Vessel Surveillance
1.1.1 Selecting appropriate dosimetric sensor sets and their
E693 Practice for Characterizing Neutron Exposures in Iron
proper installation in reactor cavities.
and Low Alloy Steels in Terms of Displacements Per
1.1.2 Making appropriate neutronics calculations to predict
Atom (DPA)
neutron radiation exposures.
E844 Guide for Sensor Set Design and Irradiation for
1.2 The values stated in SI units are to be regarded as
Reactor Surveillance
standard; units that are not SI can be found in Terminology
E854 Test Method for Application and Analysis of Solid
E170 and are to be regarded as standard. Any values in
State Track Recorder (SSTR) Monitors for Reactor Sur-
parentheses are for information only.
veillance
1.3 This practice is applicable to all pressurized water
E910 Test Method for Application and Analysis of Helium
reactors whose vessel supports will experience a lifetime Accumulation Fluence Monitors for Reactor Vessel Sur-
neutron fluence (E > 1 MeV) that exceeds 1 × 10 neutrons/
veillance
2 −4 2
cm or exceeds 3.0 × 10 dpa (1). (See Terminology E170.) E944 Guide for Application of Neutron Spectrum Adjust-
ment Methods in Reactor Surveillance
1.4 Exposure of vessel support structures by gamma radia-
E1005 Test Method for Application and Analysis of Radio-
tion is not included in the scope of this practice, but see the
metric Monitors for Reactor Vessel Surveillance
brief discussion of this issue in 3.2.
E1018 Guide for Application of ASTM Evaluated Cross
1.5 This standard does not purport to address all of the
Section Data File
safety concerns, if any, associated with its use. It is the
E2956 Guide for Monitoring the Neutron Exposure of LWR
responsibility of the user of this standard to establish appro-
Reactor Pressure Vessels
priate safety, health, and environmental practices and deter-
2.2 ASME Standard:
mine the applicability of regulatory limitations prior to use.
Boiler and Pressure Vessel Code, Section III
(For example, (2).)
2.3 Nuclear Regulatory Documents:
1.6 This international standard was developed in accor-
Code of Federal Regulations, Chapter 10, Part 50, Appendix
dance with internationally recognized principles on standard-
G Fracture Toughness Requirements
ization established in the Decision on Principles for the
Code of Federal Regulations, Chapter 10, Part 50, Appendix
Development of International Standards, Guides and Recom-
H Reactor Vessel Materials Surveillance Program Re-
mendations issued by the World Trade Organization Technical
quirements
Barriers to Trade (TBT) Committee.
Regulatory Guide 1.99, Rev. 2 Effects of Residual Elements
1 3
This practice is under the jurisdiction of ASTM Committee E10 on Nuclear For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Technology and Applications and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E10.05 on Nuclear Radiation Metrology. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved June 1, 2023. Published June 2023. Originally the ASTM website.
approved in 1985. Last previous edition approved in 2018 as E1035 – 18. DOI: Available from American Society of Mechanical Engineers, 345 E. 47th St.,
10.1520/E1035-18R23. New York, NY 10017.
2 5
The boldface numbers in parentheses refer to a list of references at the end of Available from Superintendent of Documents, U.S. Government Printing
this practice. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
E1035 − 18 (2023)
on Predicted Radiation Damage on Reactor Vessel 5. Determination of Neutron Exposure Parameter Values
Materials, U.S. Nuclear Regulatory Commission, May
5.1 Neutronics Calculations—All neutronics calculations
for (a) the analysis of integral dosimetry data, and (b) the
prediction of irradiation damage exposure parameter values
3. Significance and Use
shall follow Guide E482, subject to these additional consider-
3.1 Prediction of neutron radiation effects to pressure vessel
ations that may be encountered in reactor cavities:
steels has long been a part of the design and operation of light
5.1.1 If the vessel supports do not lie within the core’s
water reactor power plants. Both the federal regulatory agen-
active height, then an asymmetric quadrature set must be
cies (see 2.3) and national standards groups (see 2.1 and 2.2)
chosen for discrete ordinates calculations that will accurately
have promulgated regulations and standards to ensure safe
reproduce the neutron transport in the direction of the supports.
operation of these vessels. The support structures for pressur-
Care must be exercised in constructing the quadrature set to
ized water reactor vessels may also be subject to similar
ensure that “ray streaming” effects in the cavity air gap do not
neutron radiation effects (1, 3-6). The objective of this
distort the calculation of the neutron transport.
practice is to provide guidelines for determining the neutron
5.1.2 If the support system is so large or geometrically
radiation exposures experienced by individual vessel supports.
complex that it perturbs the general neutron field in the cavity,
the analysis method of choice may be that of a Monte Carlo
3.2 It is known that high-energy photons can also produce
displacement damage effects that may be similar to those calculation or a combined discrete ordinates/Monte Carlo
calculation. The combined calculation involves a two or
produced by neutrons. These effects are known to be much less
at the belt line of a light water reactor pressure vessel than three-dimensional discrete or
...