ASTM D3262-03

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 3262 – 03
Standard Specification for
“Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin)
1
Sewer Pipe
This standard is issued under the fixed designation D 3262; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope* and Reinforced Plastics and Electrical Insulating Materi-
3
als
1.1 This specification covers machine-made fiberglass
3
D 883 Terminology Relating to Plastics
pipe, 8 in. (200 mm) through 144 in. (3700 mm), intended for
D 1600 Terminology for Abbreviated Terms Relating to
use in gravity-flow systems for conveying sanitary sewage,
3
Plastics
storm water, and some industrial wastes. Both glass-fiber-
D 2412 Test Method for Determination of External Loading
reinforced thermosetting-resin pipe (RTRP) and glass-fiber-
4
Characteristics of Plastic Pipe by Parallel-Plate Loading
reinforced polymer mortar pipe (RPMP) are fiberglass pipes.
D 2584 Test Method for Ignition Loss of Cured Reinforced
NOTE 1—For the purposes of this standard, polymer does not include 5
Resins
natural polymers.
D 2992 Practice for Obtaining Hydrostatic or Pressure De-
1.2 Although this specification is suited primarily for pipes
sign Basis for “Fiberglass” (Glass-Fiber-Reinforced
4
to be installed in buried applications, it may be used to the
Thermosetting-Resin) Pipe and Fittings
extent applicable for other installations such as, but not limited
D 3567 Practice for Determining Dimensions of “Fiber-
to, jacking, tunnel lining and sliplining rehabilitation of exist-
glass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
4
ing pipelines.
and Fittings
D 3681 Test Method for Chemical Resistance of “Fiber-
NOTE 2—There is no similar or equivalent ISO standard.
glass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
1.3 The values stated in inch-pound units are to be regarded 4
in a Deflected Condition
as the standard. The values given in parentheses are for
6
D 3892 Practice for Packaging/Packing of Plastics
information only.
D 4161 Specification for “Fiberglass” (Glass-Fiber-
1.4 The following safety hazards caveat pertains only to the
Reinforced Thermosetting-Resin) Pipe Joints Using Flex-
test method portion, Section 8, of this specification. This 4
ible Elastomeric Seals
standard does not purport to address all of the safety problems,
3
F 412 Terminology Relating to Plastic Piping Systems
if any, associated with its use. It is the responsibility of the user
F 477 Specification for Elastomeric Seals (Gaskets) for
of this standard to establish appropriate safety and health
4
Joining Plastic Pipe
practices and determine the applicability of regulatory limita-
2.2 AWWA Standard:
tions prior to use.
Standard C-950, Glass-Fiber Reinforced Thermosetting
7
Resin Pipe
2. Referenced Documents
2.1 ASTM Standards:
3. Terminology
2
C 33 Specification for Concrete Aggregates
3.1 Definitions:
3
D 638 Test Method for Tensile Properties of Plastics
3.1.1 General—Unless otherwise indicated, definitions are
D 695 Test Method for Compressive Properties of Rigid
in accordance with Terminology D 883 or Terminology F 412,
3
Plastics
and abbreviations are in accordance with Terminology D 1600.
D 790 Test Methods for Flexural Properties of Unreinforced
3.2 Definitions of Terms Specific to This Standard:
3.2.1 fiberglass pipe—tubular product containing glass fiber
reinforcements embedded in or surrounded by cured thermo-
1
setting resin. The composite structure may contain aggregate,
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.23 on Reinforced
Plastic Piping Systems and Chemical Equipment.
4
Current edition approved May 10, 2003. Published November 2003. Originally Annual Book of ASTM Standards, Vol 08.04.
5
approved in 1973. Last previous edition approved in 2001 as D 3262 – 01. This Annual Book of ASTM Standards, Vol 08.02.
6
specification replaces ASTM Specification D 4184. Annual Book of ASTM Standards, Vol 08.03.
2 7
Annual Book of ASTM Standards, Vol 04.02. Available from the American Water Works Association, 6666 West Quincey
3
Annual Book of ASTM Standards, Vol 08.01. Ave., Denver, CO 80235.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D 3262 – 03
D 3262-1-1-3-A for glass–fiber–reinforced aggregate and polyester resin
granular or platelet fillers, thixotropic agents, pigments, or
mortar pipe with a reinforced thermoset li
...