ASTM D2996-00

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
An American National Standard
Designation: D 2996 – 00
Standard Specification for
Filament-Wound “Fiberglass’’ (Glass-Fiber-Reinforced
1
Thermosetting-Resin) Pipe
This standard is issued under the fixed designation D 2996; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
3
1. Scope* sure of Plastic Pipe, Tubing, and Fittings
2 D 1600 Terminology for Abbreviated Terms Relating to
1.1 This specification covers machine-made reinforced
2,3
Plastics
thermosetting resin pressure pipe (RTRP) manufactured by the
D 2105 Test Method for LongitudinalTensile Properties of“
filament winding process up to 24 in. nominal size. Included
Fiberglass” (Glass-Fiber-Reinforced Thermosetting-
are a classification system and requirements for materials,
3
Resin) Pipe and Tube
mechanical properties, dimensions, performance, methods of
D 2143 Test Method for Cyclic Pressure Strength of Rein-
test, and marking.
3
forced, Thermosetting Plastic Pipe
1.2 The values stated in inch-pound units are to be regarded
D 2310 Classification for Machine-Made “Fiberglass”
as standard. The values given in parentheses are provided for
3
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
information purposes only.
D 2412 Test Method for Determination of External Loading
1.3 The following safety hazards caveat pertains only to the
3
Characteristics of Plastic Pipe by Parallel-Plate Loading
test method portion, Section 8, of this specification: This
D 2992 Practice for Obtaining Hydrostatic or Pressure De-
standard does not purport to address all of the safety problems,
sign Basis for“ Fiberglass” (Glass-Fiber-Reinforced
if any, associated with its use. It is the responsibility of the user
3
Thermosetting-Resin) Pipe and Fittings
of this standard to establish appropriate safety and health
D 3567 Practice for Determining Dimensions of “Fiber-
practices and determine the applicability of regulatory limita-
glass” (Glass-Fiber-ReinforcedThermosetting-Resin) Pipe
tions prior to use.
3
and Fittings
NOTE 1—The term “fiberglass pipe” as described in Section 3 of this 4
F 412 Terminology Relating to Plastic Piping Systems
specification applies to both reinforced thermosetting resin pipe (RTRP)
and reinforced plastic mortar pipe (RPMP). This specification covers only
3. Terminology
reinforced thermosetting resin pipe (RTRP).
3.1 Definitions:
NOTE 2—This specification is applicable to RTRP where the ratio of
3.1.1 General—Definitions are in accordance with Termi-
outside diameter to wall thickness is 10:1 or more.
NOTE 3—There is no similar or equivalent ISO Standard. nologies D 883 and F 412 and abbreviations are in accordance
with Terminology D 1600, unless otherwise indicated. The
2. Referenced Documents
abbreviation for reinforced thermosetting resin pipe is RTRP.
2.1 ASTM Standards:
3.2 Definitions of Terms Specific to This Standard:
D 618 Practice for Conditioning Plastics and Electrical
3.2.1 coating—a resin layer, with or without filler or rein-
2
Insulating Materials for Testing
forcement, or both, applied to the exterior surface of the pipe
2
D 638 Test Method for Tensile Properties of Plastics
structural wall.
2,
3
D 883 Terminology Relating to Plastics
3.2.2 fiberglass pipe—a tubular product containing glass-
D 1598 Test Method for Time-to-Failure of Plastic Pipe
fiber reinforcements embedded in or surrounded by cured
3
Under Constant Internal Pressure
thermosetting resin; the composite structure may contain
D 1599 TestMethodforShort-TimeHydraulicFailurePres-
aggregate, granular or platelet fillers, thixotropic agents, pig-
ments, or dyes; thermoplastic or thermosetting liners or coat-
ings may be included.
1
This specification is under the jurisdiction of ASTM Committee D20 on
3.2.3 filament winding—a process used to manufacture
Plastics and is the direct responsibility of Subcommittee D20.23 on Reinforced
tubular goods by winding continuous fibrous glass strand
Plastic Piping Systems and Chemical Equipment.
roving, or roving tape, saturated with liquid resin or preim-
Current edition approved Dec 10, 2000. Published February 2001. Originally
published as D 2996 – 71. Last previous edition D 2996 – 95. pregnated with partially cured resin (subsequent heating may
2
This specification was revised to include an ISO equivalency statement and a
section on keywords.
3 4
Annual Book of ASTM Standards, Vol 08.01. Annual Book of ASTM Standards, Vol 08.04.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, We
...