ASTM C655-12
(Specification)Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
ABSTRACT
This specification covers reinforced concrete pipe, D-load culvert, storm drain, and sewer pipe for the conveyance of sewage, industrial wastes, and storm water. The numerical values in this specification are not presented in inch-pound units, but rather, in metric or SI units only. The reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in which steel has been embedded in such a manner that the steel and concrete act together. The combination of cementitious materials used in the concrete shall be only one of the following: Portland cement, Portland blast furnace slag cement, slag modified Portland cement, Portland pozzolan cement, a combination of Portland cement and fly ash, a combination of Portland cement and ground granulated blast-furnace slag, or a combination of Portland cement, ground granulated blast furnace slag, and fly ash. Reinforcement shall conform to the standard specification. Physical requirements shall conform to the design strength designation of the pipe during load test. The aggregates shall be sized, graded, proportioned, and mixed with such proportions of cementitious materials and water as will produce a homogeneous concrete mixture of such quality that the pipe shall conform to the test and design requirements of this specification. The strength of the pipe shall not be adversely affected by the splice. Compression tests for determining concrete compressive strength shall be allowed to be made on either concrete cylinders or on cores drilled from the pipe. Pipe shall be repaired, if necessary, because of imperfections in manufacture, damage during handling, or pipe that have been cored for testing.
SCOPE
1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts.
1.2 A complete metric companion to Specification C655 has been developedSpecification C655M; therefore, no metric equivalents are presented in this specification.
Note 1—Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C655 −12
StandardSpecification for
Reinforced Concrete D-Load Culvert, Storm Drain, and
1
Sewer Pipe
This standard is issued under the fixed designation C655; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C989 Specification for Slag Cement for Use in Concrete and
Mortars
1.1 This specification covers reinforced concrete pipe de-
C1116 Specification for Fiber-Reinforced Concrete and
signed for specific D-loads and intended to be used for the
Shotcrete
conveyance of sewage, industrial wastes, and storm water and
E105 Practice for Probability Sampling of Materials
for the construction of culverts.
1.2 Acomplete metric companion to Specification C655 has
3. Terminology
been developed—Specification C655M; therefore, no metric
3.1 Definitions—Fordefinitionsoftermsrelatingtoconcrete
equivalents are presented in this specification.
pipe, see Terminology C822.
NOTE 1—Experience has shown that the successful performance of this
product depends upon the proper selection of the pipe strength, the type of
4. Basis of Acceptance
bedding and backfill, the care that the installation conforms to the
4.1 The acceptability of the pipe design shall be determined
construction specifications, and provision for adequate inspection at the
construction site. This specification does not include requirements for in accordance with Section 9. After the pipe design has been
bedding, backfill, the relationship between field load conditions and the
accepted, or if the pipe design has been accepted previously in
strength designation of pipe, or durability under unusual environmental
accordance with Section 9, the owner may select and have
conditions. These requirements should be included in the project specifi-
applied the basis of acceptance described in either 4.1.1 or
cation.
4.1.2. Unless designated by the owner at the time of, or before
2. Referenced Documents
placing an order, either basis of acceptance shall be permitted.
2
4.1.1 Acceptance on the Basis of Pipe Load and Material
2.1 ASTM Standards:
A615/A615M SpecificationforDeformedandPlainCarbon- Tests and Inspection of Manufactured Pipe for Defects—
Determine in accordance with Sections 5, 6, 8, and 10.
Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Steel Wire and Welded
NOTE 2—It is necessary that samples be selected at random. For
Wire Reinforcement, Plain and Deformed, for Concrete
guidance see Practice E105.
C33 Specification for Concrete Aggregates
4.1.2 AcceptanceontheBasisofConcreteCompression and
C150 Specification for Portland Cement
Materials Tests and Inspection of Manufactured Pipe for
C497 Test Methods for Concrete Pipe, Manhole Sections, or
Defects—DetermineinaccordancewithSections5,6,8and 11.
Tile
4.2 Age for Acceptance—Pipe shall be considered ready for
C595 Specification for Blended Hydraulic Cements
acceptance when they conform to the requirements.
C618 Specification for Coal Fly Ash and Raw or Calcined
Natural Pozzolan for Use in Concrete
5. Design and Manufacturing Data
C822 Terminology Relating to Concrete Pipe and Related
Products
5.1 The manufacturer shall provide the following informa-
tion regarding the pipe unless waived by the owner:
1
This specification is under the jurisdiction of ASTM Committee C13 on
5.1.1 Basis of acceptance.
Concrete Pipe and is the direct responsibility of Subcommittee C13.02 on
5.1.2 Pipe design strength.
Reinforced Sewer and Culvert Pipe.
5.1.3 Physical Characteristics—Diameter, wall thickness,
Current edition approved May 1, 2012. Published June 2012. Originally
laying length, and joint details.
approved in 1970. Last previous edition approved in 2011 as C655 – 11. DOI:
10.1520/C0655-12.
5.1.4 Design concrete strength; minimum f ` equals 4000
c
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
psi.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5.1.5 Admixtures.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 5.1.6 Reinforcement:
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C655 − 12
5.1.6.1 Type of reinforcement, applicable reinforcement and shall be added to the mix in a proportion not less than 470
3
specification, and grade. lb/yd unless mix designs with a lower cementitious material
5.1.6.2 Placement, placement tolerances, diameter, spacing content demonstrate that the quality and p
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C655–11 Designation: C655 – 12
Standard Specification for
Reinforced Concrete D-Load Culvert, Storm Drain, and
1
Sewer Pipe
This standard is issued under the fixed designation C655; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance
of sewage, industrial wastes, and storm water and for the construction of culverts.
1.2 A complete metric companion to Specification C655 has been developed—Specification C655M; therefore, no metric
equivalents are presented in this specification.
NOTE 1—Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of
bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction
site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of
pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.
2. Referenced Documents
2
2.1 ASTM Standards: A82/A82MSpecification for Steel Wire, Plain, for Concrete Reinforcement
A185/A185MSpecification for Steel Welded Wire Reinforcement, Plain, for Concrete
A496/A496MSpecification for Steel Wire, Deformed, for Concrete Reinforcement
A497/A497MSpecification for Steel Welded Wire Reinforcement, Deformed, for Concrete
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
C33 Specification for Concrete Aggregates
C150 Specification for Portland Cement
C497 Test Methods for Concrete Pipe, Manhole Sections, or Tile
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C822 Terminology Relating to Concrete Pipe and Related Products
C989 Specification for Slag Cement for Use in Concrete and Mortars
C1116 Specification for Fiber-Reinforced Concrete and Shotcrete
E105 Practice for Probability Sampling of Materials
3. Terminology
3.1 Definitions—For definitions of terms relating to concrete pipe, see Terminology C822.
4. Basis of Acceptance
4.1 The acceptability of the pipe design shall be determined in accordance with Section 9. After the pipe design has been
accepted, or if the pipe design has been accepted previously in accordance with Section 9, the owner may select and have applied
the basis of acceptance described in either 4.1.1 or 4.1.2. Unless designated by the owner at the time of, or before placing an order,
either basis of acceptance shall be permitted.
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.02 on Reinforced Sewer
and Culvert Pipe.
Current edition approved Jan. 15, 2011. Published February 2011. Originally approved in 1970. Last previous edition approved in 2009 as C655–09. DOI:
10.1520/C0655-11.
Current edition approved May 1, 2012. Published June 2012. Originally approved in 1970. Last previous edition approved in 2011 as C655 – 11. DOI: 10.1520/C0655-12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C655 – 12
4.1.1 Acceptance on the Basis of Pipe Load and Material Tests and Inspection of Manufactured Pipe for Defects—Determine
in accordance with Sections 5, 6, 8, and 10.
NOTE 2—It is necessary that samples be selected at random. For guidance see Practice E105.
4.1.2 Acceptance on the Basis of Concrete Compression and Materials Tests and Inspection of Manufactured Pipe for
Defects—Determine in accordance with Sections 5, 6, 8 and 11.
4.2 Age fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.