ASTM F803-01

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 803 – 01
Standard Specification for
1
Eye Protectors for Selected Sports
This standard is issued under the fixed designation F803; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (ε) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
1.1 This specification covers eye protectors, designed for 2.1 ASTM Standards:
2
usebyplayersofracketsports,women’slacrosse,fieldhockey, B117 Practice for Operating Salt Spray (Fog) Apparatus
3
basketball, and baseball that minimize or significantly reduce D570 Test Method for Water Absorption of Plastics
injury to the eye and adnexa due to impact and penetration by D1003 Test Method for Haze and LuminousTransmittance
3
racket-sport rackets and balls, women’s lacrosse and field of Transparent Plastics
hockey sticks and balls, baseballs, and hands, elbows, and F1776 Specification for Eye Protective Devices for Paint-
4
fingers. Protective eyewear offers protection only to the eyes ball Sports
and does not protect other parts of the head. 2.2 American National Standards:
1.2 Protectorsaredividedintofourtypesdependingontheir ANSI Z80.1 Requirements for First-Quality Prescription
5
design characteristics. Ophthalmic Lenses
1.3 This specification applies to eye protectors for use by ANSI Z80.3 Requirements for Nonprescription Sunglasses
5
wearers of corrective lenses and also by those players who do and Fashion Eyewear
not require prescription eyewear. ANSIZ87.1 PracticeforOccupationalandEducationalEye
5
and Face Protectors
NOTE 1—Warning:Polycarbonate spectacle lenses should be used if
2.3 Federal Standard:
spectacles are worn under protective eyewear.
National Institute of Standards and Technology Special
1.4 In this standard, the use of the words “shall” or “must”
Technical Publication 374 Method for Determining the
indicates a mandatory requirement. The word “should” indi-
6
Resolving Power of Photographic Lenses (1973)
cates a recommendation.
1.5 The values stated in SI units are to be regarded as the
3. Terminology
standard. The values given in parentheses are for information
3.1 Definitions of Terms Specific to This Standard:
only. Metric units of measurement in this specification are in
3.1.1 binocular, adj—relating to the field of view which is
accordance with the International System of Units (SI). If a
shared by both eyes simultaneously; also any simultaneous
valueformeasurementasgiveninthisspecificationisfollowed
activity of the two eyes.
by an equivalent value in other units, the first stated is to be
3.1.2 central viewing zone, n—that part of the eye of a
regarded as the requirement.Agiven equivalent value may be
protector, which has its center in line with the wearer’s normal
approximate.
line of sight. The zone is circular in shape, and 40 mm in
1.6 The following precautionary caveat pertains only to the
diameter. The center of the central viewing zone shall be the
test methods portions, Sections 9-11, of this specification: This
point of intersection of the line of sight with the lens as
standard does not purport to address all of the safety concerns, 7
mounted on the CSA headform.
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health
2
practices and determine the applicability of regulatory limita-
Annual Book of ASTM Standards, Vol 03.02.
3
Annual Book of ASTM Standards, Vol 08.01.
tions prior to use.
4
Annual Book of ASTM Standards, Vol 15.07.
5
Available from American National Standards Institute, 11 W. 42nd St., 13th
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports Floor, New York, NY 10036.
6
EquipmentandFacilitiesandisthedirectresponsibilityofSubcommitteeF08.57on Available from National Institute of Standards and Technology, U.S. Depart-
Eye Safety for Sports. ment of Commerce, Washington, DC 20234.
7
Current edition approved May 10, 2001. Published September 2001. Originally Available from Canadian Standards Association, Etobicoke (Toronto), 178
published as F803–83. Last previous edition F803–00. Rexdale Boulevard, Etobicoke (Toronto), ON M9W 1R3.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F803–01
3.1.3 cleanable, n—the ability of a protective device to be 3.1.7 eye of the headform, n—all structures contained
7
made readily free of dirt or grime without being damaged within the orbital rim of the CSA headform.
duringanappropriatecleaningprocess,suchastheuseofsoap
3.1.8 haze, n—the fraction of the total transm
...