ASTM D243/D243M-22
(Test Method)Standard Test Method for Residue of Specified Penetration
Standard Test Method for Residue of Specified Penetration
SIGNIFICANCE AND USE
5.1 This test method is used to determine the percentage of residue having a specified penetration at 100 g/5 s at 25 °C [77 °F]. This test method provides a residue for quality control or for use in other tests as desired.
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method is used to thermally reduce cutback asphalt, a road oil or a semisolid asphalt, having a penetration greater than 100, to a residue of specified penetration. It is primarily used with slow-curing cutback asphalt as specified in Specification D2026/D2026M.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, into your state may be prohibited by state law.
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D243/D243M −22
Standard Test Method for
1
Residue of Specified Penetration
This standard is issued under the fixed designation D243/D243M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
1.1 This test method is used to thermally reduce cutback
Barriers to Trade (TBT) Committee.
asphalt, a road oil or a semisolid asphalt, having a penetration
greater than 100, to a residue of specified penetration. It is
2. Referenced Documents
primarily used with slow-curing cutback asphalt as specified in
2
2.1 ASTM Standards:
Specification D2026/D2026M.
D5/D5M Test Method for Penetration of Bituminous Mate-
1.2 The values stated in either SI units or inch-pound units
rials
are to be regarded separately as standard. The values stated in
D8 Terminology Relating to Materials for Roads and Pave-
each system are not necessarily exact equivalents; therefore, to
ments
ensure conformance with the standard, each system shall be
D2026/D2026M Specification for Cutback Asphalt (Slow-
used independently of the other, and values from the two
Curing Type)
systems shall not be combined.
D3666 Specification for Minimum Requirements for Agen-
1.3 Warning—Mercury has been designated by the United cies Testing and Inspecting Road and Paving Materials
States Environmental ProtectionAgency (EPA) and many state D8055 Guide for Selecting an Appropriate Electronic Ther-
agencies as a hazardous material that can cause central nervous mometer for Replacing Mercury Thermometers in D04
system, kidney, and liver damage. Mercury, or its vapor, may Road and Paving Standards
be hazardous to health and corrosive to materials. Caution E1 Specification for ASTM Liquid-in-Glass Thermometers
should be taken when handling mercury and mercury- E230/E230M Specification for Temperature-Electromotive
containing products. See the applicable product Material Force (emf) Tables for Standardized Thermocouples
3
Safety Data Sheet (MSDS) for details and EPA’s website— 2.2 IEC Standards:
http://www.epa.gov/mercury/—for additional information. Us- IEC60584 Thermocouples—Part3:ExtensionandCompen-
ers should be aware that selling mercury, mercury-containing sating Cables—Tolerances and Identification System
products, or both, into your state may be prohibited by state
3. Terminology
law.
3.1 Definitions of terms used in this practice may be found
1.4 The text of this standard references notes and footnotes
in Terminology D8, determined from common English usage,
which provide explanatory material. These notes and footnotes
or combinations of both.
(excluding those in tables and figures) shall not be considered
as requirements of the standard.
4. Summary of Test Method
1.5 This standard does not purport to address all of the
4.1 The material to be tested is rapidly heated to 249 °C
safety concerns, if any, associated with its use. It is the
[480 °F] and maintained at 249 to 260 °C [480 to 500 °F]
responsibility of the user of this standard to establish appro-
duringevaporationofthevolatiles.Penetrationoftheresidueis
priate safety, health, and environmental practices and deter-
determined and if not within the specified limits, the evapora-
mine the applicability of regulatory limitations prior to use.
tion procedure is repeated. Change in sample mass is used to
1.6 This international standard was developed in accor-
calculate the percentage of residue having the specified pen-
dance with internationally recognized principles on standard-
etration.
ization established in the Decision on Principles for the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This test method is under the jurisdiction of ASTM Committee D04 on Road contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Paving Materials and is the direct responsibility of Subcommittee D04.46 on Standards volume information, refer to the standard’s Document Summary page on
Durability and Distillation Tests. the ASTM website.
3
Current edition approved Aug. 1, 2022. Published August 2022. Originally Available from International Electrotechnical Commission (IEC), 3, rue de
approved in 1926. Last previous edition approved in 2020 as D243/D243M – 20. Varembé, 1st floor, P.O. Box 131, CH-1211, Geneva 20, Switzerland, https://
DOI: 10.1520/D0243_D0243M-22. www.iec.ch.
Copyright © ASTM Int
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D243/D243M − 20 D243/D243M − 22
Standard Test Method for
1
Residue of Specified Penetration
This standard is issued under the fixed designation D243/D243M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method is used to thermally reduce cutback asphalt, a road oil or a semisolid asphalt, having a penetration greater
than 100, to a residue of specified penetration. It is primarily used with slow-curing cutback asphalt as specified in Specification
D2026/D2026M.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used
independently of the other, and values from the two systems shall not be combined.
1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state
agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be
hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products.
See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/—for
additional information. Users should be aware that selling mercury, mercury-containing products, or both, into your state may be
prohibited by state law.
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D5/D5M Test Method for Penetration of Bituminous Materials
D8 Terminology Relating to Materials for Roads and Pavements
D2026/D2026M Specification for Cutback Asphalt (Slow-Curing Type)
1
This test method is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.46 on Durability
and Distillation Tests.
Current edition approved Nov. 1, 2020Aug. 1, 2022. Published November 2020August 2022. Originally approved in 1926. Last previous edition approved in 20142020
as D243/D243M – 14.D243/D243M – 20. DOI: 10.1520/D0243_D0243M-20.10.1520/D0243_D0243M-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D243/D243M − 22
D3666 Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
D8055 Guide for Selecting an Appropriate Electronic Thermometer for Replacing Mercury Thermometers in D04 Road and
Paving Standards
E1 Specification for ASTM Liquid-in-Glass Thermometers
E77E230/E230M Test Method for Inspection and Verification of ThermometersSpecification for Temperature-Electromotive
Force (emf) Tables for Standardized Thermocouples
E563 Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
E644 Test Methods for Testing Industrial Resistance Thermometers
3
2.2 IEC Standards:
IEC 60584 Thermocouples—Part 3: Extension and Compensating Cables—Tolerances and Identification System
3. Terminology
3.1 Definitions of terms used in this practice may be found in Terminology D8, determined from common English usage, or
combi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.