Standard Specification for Ready-Mixed Concrete

ABSTRACT
This specification covers ready-mixed concrete manufactured and delivered to a purchaser in freshly mixed and unhardened state as hereinafter specified. Requirements for quality of concrete shall be either as hereinafter specified or as specified by the purchase. In any case where the requirements of the purchaser differ from these in this specification, the purchaser's specification shall govern. In the absence of designated applicable materials specifications, materials specifications specified shall be used for cementitious materials, hydraulic cement, supplementary cementitious materials, cementitious concrete mixtures, aggregates, air-entraining admixtures, and chemical admixtures. Except as otherwise specifically permitted, cement, aggregate, and admixtures shall be measured by mass. Mixers will be stationary mixers or truck mixers. Agitators will be truck mixers or truck agitators. Test methods for compression, air content, slump, temperature shall be performed. For s strength test, at least two standard test specimens shall be made.
SCOPE
1.1 This specification covers ready-mixed concrete as defined in 3.2.2 (Note 1). Requirements for quality of ready-mixed concrete shall be either as stated in this specification or as ordered by the purchaser. When the purchaser’s requirements, as stated in the order, differ from those in this specification, the purchaser’s requirements shall govern. This specification does not cover the placement, consolidation, curing, or protection of the concrete after delivery to the purchaser.
Note 1: Concrete produced by volumetric batching and continuous mixing is covered in Specification C685. Fiber-reinforced concrete is covered in Specification C1116.  
1.2 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 As used throughout this specification the manufacturer produces ready-mixed concrete. The purchaser buys ready-mixed concrete.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged use.2)

General Information

Status
Historical
Publication Date
31-Jul-2015
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM C94/C94M-15a - Standard Specification for Ready-Mixed Concrete
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM C94/C94M-15a - Standard Specification for Ready-Mixed Concrete
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C94/C94M −15a
StandardSpecification for
1
Ready-Mixed Concrete
This standard is issued under the fixed designation C94/C94M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
3
1.1 This specification covers ready-mixed concrete as de- 2.1 ASTM Standards:
fined in 3.2.2 (Note 1). Requirements for quality of ready- C31/C31M Practice for Making and Curing Concrete Test
mixed concrete shall be either as stated in this specification or Specimens in the Field
as ordered by the purchaser. When the purchaser’s C33/C33M Specification for Concrete Aggregates
requirements, as stated in the order, differ from those in this C39/C39M Test Method for Compressive Strength of Cylin-
specification, the purchaser’s requirements shall govern. This drical Concrete Specimens
specification does not cover the placement, consolidation, C125 Terminology Relating to Concrete and Concrete Ag-
curing, or protection of the concrete after delivery to the gregates
purchaser. C138/C138M Test Method for Density (Unit Weight),Yield,
and Air Content (Gravimetric) of Concrete
NOTE 1—Concrete produced by volumetric batching and continuous
C143/C143M Test Method for Slump of Hydraulic-Cement
mixing is covered in Specification C685. Fiber-reinforced concrete is
Concrete
covered in Specification C1116.
C150/C150M Specification for Portland Cement
1.2 The values stated in either SI units, shown in brackets,
C172/C172M Practice for Sampling Freshly Mixed Con-
or inch-pound units are to be regarded separately as standard.
crete
The values stated in each system may not be exact equivalents;
C173/C173M Test Method forAir Content of Freshly Mixed
therefore,eachsystemshallbeusedindependentlyoftheother.
Concrete by the Volumetric Method
Combining values from the two systems may result in non-
C231/C231M Test Method forAir Content of Freshly Mixed
conformance with the standard.
Concrete by the Pressure Method
1.3 As used throughout this specification the manufacturer
C260/C260M Specification for Air-Entraining Admixtures
produces ready-mixed concrete. The purchaser buys ready-
for Concrete
mixed concrete.
C330/C330M Specification for Lightweight Aggregates for
1.4 The text of this standard references notes and footnotes Structural Concrete
C494/C494M Specification for Chemical Admixtures for
which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered Concrete
C567/C567M Test Method for Determining Density of
as requirements of the standard.
Structural Lightweight Concrete
1.5 This standard does not purport to address all the safety
C595/C595M Specification for Blended Hydraulic Cements
concerns, if any, associated with its use. It is the responsibility
C618 Specification for Coal Fly Ash and Raw or Calcined
of the user of this standard to establish appropriate safety and
Natural Pozzolan for Use in Concrete
health practices and determine the applicability of regulatory
C637 Specification for Aggregates for Radiation-Shielding
limitations prior to use. (Warning—Fresh hydraulic cementi-
Concrete
tious mixtures are caustic and may cause chemical burns to
2
C685 Specification for Concrete Made byVolumetric Batch-
skin and tissue upon prolonged use. )
ing and Continuous Mixing
C989/C989M Specification for Slag Cement for Use in
1 Concrete and Mortars
This specification is under the jurisdiction of ASTM Committee C09 on
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
C09.40 on Ready-Mixed Concrete.
Current edition approved Aug. 1, 2015. Published October 2015. Originally
3
approved in 1933. Last previous edition approved in 2015 as C94/C94M – 15. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/C0094_C0094M-15A. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
See Section on Safety Precautions, Manual ofAggregate and Concrete Testing, Standards volume information, refer to the standard’s Document Summary page on
Annual Book of ASTM Standards, Vol 04.02. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C94/C94M−15a
C1017/C1017M Specification for Chemical Admixtures for 4.2 The volume of fresh concrete in a given batch shall be
Use in Producing Flowing Concrete determined from the
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C94/C94M − 15 C94/C94M − 15a
Standard Specification for
1
Ready-Mixed Concrete
This standard is issued under the fixed designation C94/C94M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers ready-mixed concrete as defined in 3.2.2 (Note 1). Requirements for quality of ready-mixed
concrete shall be either as stated in this specification or as ordered by the purchaser. When the purchaser’s requirements, as stated
in the order, differ from those in this specification, the purchaser’s requirements shall govern. This specification does not cover the
placement, consolidation, curing, or protection of the concrete after delivery to the purchaser.
NOTE 1—Concrete produced by volumetric batching and continuous mixing is covered in Specification C685. Fiber-reinforced concrete is covered in
Specification C1116.
1.2 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The
values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
Combining values from the two systems may result in non-conformance with the standard.
1.3 As used throughout this specification the manufacturer produces ready-mixed concrete. The purchaser buys ready-mixed
concrete.
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.5 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of
the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and
2
tissue upon prolonged use. )
2. Referenced Documents
3
2.1 ASTM Standards:
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C125 Terminology Relating to Concrete and Concrete Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C150/C150M Specification for Portland Cement
C172/C172M Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C260/C260M Specification for Air-Entraining Admixtures for Concrete
C330/C330M Specification for Lightweight Aggregates for Structural Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C567/C567M Test Method for Determining Density of Structural Lightweight Concrete
1
This specification is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.40 on
Ready-Mixed Concrete.
Current edition approved Feb. 1, 2015Aug. 1, 2015. Published May 2015October 2015. Originally approved in 1933. Last previous edition approved in 20142015 as
C94/C94M – 14b.15. DOI: 10.1520/C0094_C0094M-15.10.1520/C0094_C0094M-15A.
2
See Section on Safety Precautions, Manual of Aggregate and Concrete Testing, Annual Book of ASTM Standards, Vol 04.02.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C94/C94M − 15a
C595/C595M Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C637 Specification for Aggregates for
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.