ASTM F2388-08a

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F 2388–08 Designation: F 2388 – 08a
Standard Consumer Safety Specification for
1
Baby Changing Tables for Domestic Use
This standard is issued under the fixed designation F 2388; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
This consumer safety specification addresses incidents associated with baby changing tables
identified by the U.S. Consumer Product Safety Commission (CPSC). Incidents involved collapse,
falls from the table, and entrapment in structural members.
In response to incident data collected by CPSC, this consumer safety specification attempts to
minimize the risk of injury and death due to: (1) falls from changing tables, (2) failure of structural
or mechanical components, (3) instability and entrapment in openings in the table structure. This
specification also contains requirements for warnings and instructional materials directed to parents or
caregivers.
1. Scope
1.1 This consumer safety specification covers performance requirements, test methods, and labeling requirements to promote
the safe use of baby changing tables and other changing surfaces such as contoured changing pads and add-on changing units that
are sold separately for use on furniture products other than changing tables.
1.2 This specification covers products sold for domestic use for children up to a weight of 30 lb (13.6 kg).
1.3 Changing tables and other changing products sold separately, such as contoured changing pads and add-on changing units
shall meet all applicable performance and labeling requirements.
1.4 No changing table, contoured changing pad, or add-on changing unit produced after the approval date of this specification
shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements
contained herein, before, and after all testing.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion in Section 7 of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to
use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 3359 Test Methods for Measuring Adhesion by Tape Test
F 406 Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards
F 963 Consumer Safety Specification for Toy Safety
3
2.2 Federal Regulations:
16 CFR 1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint
16 CFR 1500 Hazardous Substances Act Regulations including sections:
16 CFR 1500.48 Technical Requirements for Determining a Sharp Point inToys or OtherArticles Intended for Use by Children
Under Eight Years of Age
16 CFR 1500.49 Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or OtherArticles Intended for
Use by Children Under Eight Years of Age
1
This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.18
on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables.
Current edition approved MayJuly 1, 2008. Published JuneAugust 2008. Originally approved in 2004. Last previous edition approved in 20062008 as F 2388 – 068.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from U.S. Consumer Product Safety Commission (CPSC), Washington, D.C. 20207, website: www.cpsc.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 2388 – 08a
16 CFR 1500.50-.52 Test Methods for Simulating Use and Abuse of Toys and Other Articles Intended for Use by Children
16 CFR 1501 Method for Identifying Toys and Other Ar
...