ISO/TC 131/SC 7/WG 4 - Rotary shaft lip type seals
Bagues d'étanchéité à lèvres pour arbres rotatifs
General Information
- Standard2 pagesEnglish languagesale 15% off
ISO 16589-2:2011 establishes the vocabulary for seals utilizing sealing elements manufactured from suitably formulated compounds, based on thermoplastic materials, such as polytetrafluoroethylene (PTFE) that are considered suitable for use under low-pressure conditions.
- Standard38 pagesEnglish and French languagesale 10% offe-Library read for1 day
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds, based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low-pressure conditions. ISO 16589-3:2011 gives users of lip-type seals guidance on the careful storage and handling and proper installation of rotary shaft lip-type seals; attention is drawn to the hazards involved and ways of avoiding them are pointed out.
- Standard9 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low-pressure conditions. ISO 16589-5:2011 defines and classifies typical surface imperfections that could impair the function of the seals, and is intended as a convenience for purchasers and manufacturers in their discussions concerning the importance of these imperfections in different applications.
- Standard14 pagesEnglish languagesale 15% off
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low-pressure conditions. ISO 16589-4:2011 specifies general performance tests which can be used for seal qualification purposes. Materials quality control, dynamic testing, and supplementary low-temperature testing requirements are covered.
- Standard15 pagesEnglish languagesale 15% off
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 16589 specifies seals utilizing sealing elements manufactured from suitably formulated compounds based on thermoplastic materials, such as polytetrafluoroethylene (PTFE). They are considered suitable for use under low-pressure conditions. ISO 16589-1:2011 shows seal types and examples. It also specifies the nominal dimensions and tolerance of the seals, shafts and housings, as well as a dimensional identification code.
- Standard13 pagesEnglish languagesale 15% off
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 6194 describes seals utilizing elastomeric sealing elements. They are considered suitable for use under low-pressure conditions. ISO 6194-4:2009 specifies general test requirements for rotary-shaft lip-type seals. The tests may be used for qualification purposes.
- Standard17 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
ISO 6194-5:2008 describes seals utilizing elastomeric sealing elements. They are normally considered suitable for use only at low pressures (see ISO 6194-1:2007, 6.1). ISO 6194-5:2008 defines and classifies typical surface imperfections that can impair the function of the seals and is intended as a convenience for purchasers and manufacturers in their discussions concerning the importance of these imperfections in different applications.
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
ISO 6194-1:2007 describes seals utilising elastomeric sealing elements. They are considered suitable for use under low-pressure conditions. ISO 6194-1:2007 shows seal types and examples. It also specifies the nominal dimensions and tolerances of the seals, shafts and housings, as well as a dimensional identification code.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard13 pagesFrench languagesale 15% off
- Standard17 pagesEnglish and French languagesale 10% offe-Library read for1 day
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard10 pagesFrench languagesale 15% off
- Standard18 pagesEnglish languagesale 15% off
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard18 pagesFrench languagesale 15% off
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard15 pagesFrench languagesale 15% off
- Standard15 pagesEnglish languagesale 15% off
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard15 pagesFrench languagesale 15% off