77.120.60 - Lead, zinc, tin and their alloys

This document specifies requirements for the protection of iron and steel surfaces against corrosion by
applying thermal-sprayed metallic coatings of zinc, aluminium or their alloys.
In this document, requirements for the planning of the corrosion protection system and for the
constructive design of the component to be protected are specified, where thermal spraying is intended
to be the process for the deposition of the metallic corrosion protection.
Some field-related basic terms are defi...view more

This document specifies requirements for corrosion protection of steel structures, components or
parts, which are coated by thermal spraying of zinc, aluminium or their alloys.
This document specifies requirements for coating manufacturers of surface preparation, thermal
spraying, testing and post treatments, e.g. sealing of the coating. This document applies to metallic
corrosion protection coatings in the case of new fabrication in the workshop, as well as on-site and for
repair on-site a...view more

This standard applies to electrodeposited zinc and zinc-alloy coatings on iron and steel with Cr(VI)-free passivation. The zinc-alloy coatings contain nickel or iron as alloying elements (referred to as zinc/nickel and zinc/iron coatings, respectively).
The main purpose of the coatings or coating systems is protecting iron and steel components against corrosion.
This standard specifies
- the designations to be used for the above coating systems
-minimum corrosion resistance to be achieved in spe...view more

This ISO standard specifies minimum thickness requirements for six classes of zinc coating applied to ferrous products by the sherardizing process for the purpose of protection against corrosion and wear. It also specifies the minimum requirements of the zinc dust to be used in the sherardizing process. This standard does not specifiy any requirements for the surface condition (finish or roughness) of the basis material before sherardizing.
After-treatments or organic over-coatings of sherardize...view more

This International Standard specifies requirements for bearing metals based on tin casting alloys for multilayer
plain bearings. The chemical composition and material properties refer to the original unprocessed material
and are measured on representative samples. Testing results on final bearings can differ due to the influence
of bearing production. Therefore, it is not intended that these results be compared with data given in this
International Standard.

ISO 4381:2011 specifies requirements for bearing metals based on tin casting alloys for multilayer plain bearings. The chemical composition and material properties refer to the original unprocessed material and are measured on representative samples. Testing results on final bearings can differ due to the influence of bearing production. Therefore, it is not intended that these results be compared with data given in ISO 4381:2011.

This European Standard specifies a spectrophotometric method for the determination of silicon in zinc alloys. It is applicable to the products specified in EN 1774 and EN 12844. It is suitable for the determination of silicon contents (mass fractions) between 0,01% and 0,1%.

ISO 301:2006 specifies the designations, chemical compositions, marking and other requirements for zinc alloys, in ingots (or liquid form), produced for foundry purposes.

This European Standard specifies a spectrophotometric method for the determination of silicon in zinc alloys. It is applicable to the products specified in EN 1774 and EN 12844.
It is suitable for the determination of silicon contents (mass fractions) between 0,01 % and 0,1 %.

ISO 1169:2006 specifies a titrimetric method for the determination of aluminium in zinc alloys. It is applicable to the products specified in ISO 301. It is suitable for the determination of aluminium contents (mass fractions) between 3 % and 30 %.

ISO 3750:2006 specifies a flame atomic absorption spectrometric method for the determination of magnesium in zinc alloys. It is applicable to the products specified in ISO 301 and ISO 752. It is suitable for the determination of magnesium contents (mass fractions) between 0,002 % and 0,08 %.

Migrated from Progress Sheet (TC Comment) (2000-07-10): Revision of EN 12019:1997 into 2 parts; see also WI 023 (TC Res 58/1998) (CC/990114) ++ New TD given by TC (bli 00208)

ISO 3815-2:2005 specifies analytical methods for determining the chemical composition of zinc and zinc alloys in accordance with ISO 301 and ISO 752 by inductively coupled optical emission spectrometry. ISO 3815-2:2005 includes provisions for preparation of test solutions and calibration solutions for zinc and zinc alloys. The ranges specified for each method can be extended and/or adapted for determinations of low concentrations. ISO 3815-2:2005 can be applied to other elements (e.g. Ni, Cr and...view more

ISO 3815-2:2005 specifies analytical methods for determining the chemical composition of zinc and zinc alloys in accordance with ISO 301 and ISO 752 by inductively coupled optical emission spectrometry.
ISO 3815-2:2005 includes provisions for preparation of test solutions and calibration solutions for zinc and zinc alloys.
The ranges specified for each method can be extended and/or adapted for determinations of low concentrations.
ISO 3815-2:2005 can be applied to other elements (e.g. Ni, Cr ...view more

Migrated from Progress Sheet (TC Comment) (2000-07-10): Revision of EN 12019:1997 into 2 parts; see also WI 024 (TC Res 58/1998) (CC/990114) ++ VA/ISO (TC Res 77/2000) (CC/010913)

ISO 3815-1:2005 specifies analytical methods for determining the chemical composition of zinc and zinc alloys in accordance with ISO 301 and ISO 752 by optical emission spectrometry. ISO 3815-1:2005 includes recommendations for preparation of test pieces from zinc and zinc alloys.

ISO 3815-1:2005 specifies analytical methods for determining the chemical composition of zinc and zinc alloys in accordance with ISO 301 and ISO 752 by optical emission spectrometry.
ISO 3815-1:2005 includes recommendations for preparation of test pieces from zinc and zinc alloys.

ISO 20081:2005 specifies the requirements for sampling of zinc and zinc alloys, as specified in ISO 752 and ISO 301, for analysis.

This document specifies a flame atomic absorption spectrometric method for the determination of tin in secondary zinc. It is applicable to the products specified in EN 13283.
It is suitable for the determination of tin contents (mass fractions) between 0,1 % and 1,0 %.

This document specifies a flame atomic absorption spectrometric method after extraction for the determination of tin in zinc and zinc alloys. It is applicable to the products specified in EN 988, EN 1179, EN 1774 and EN 12844.
It is suitable for the determination of tin contents (mass fractions) between 0,000 5 % and 0,005 %.