75.040 - Crude petroleum

This European standard describes a method for the determination of the boiling range distribution of petroleum products by capillary gas chromatography using flame ionisation detection. The standard is applicable to crude oils. The boiling range distribution and recovery to C100 or C120 can be determined.Two procedures are described: single and dual analysis mode. The basis of each is the calculation procedure as described in Annex A.

This European Standard defines the methods of tests for the determination of the characteristics of crude tar and crude benzole.

Migrated from Progress Sheet (TC Comment) (2000-07-10): TC Res.5/1999: Revision of EN ISO 3838:1995 under // vote ISO lead. However in ++ ISO, it is not formal yet, Mr. Williams is being asked to check (TA/990702) ++  New TC forecasts in rev BP (NT/01-01-02)

ISO 3838:2004 specifies methods for the determination of the density or relative density of crude petroleum and of petroleum products handled as liquids.
The capillary-stoppered pyknometer method is also for use with solids and this method may also be used for coal tar products, including road tars, creosote and tar pitches, or for mixtures of these with petroleum products. This method is not suitable for the determination of the density or relative density of highly volatile liquids having Rei...view more

This International Standard specifies a method for the determination of the vapour pressure of liquid petroleum
products consisting of essentially or wholly of hydrocarbon components, or containing oxygenated hydrocarbons of
specific types and at specified maximum concentrations. The method does not apply outside these concentration
levels, nor to any blends containing methanol or other oxygenated hydrocarbons not covered in note 1.
NOTE 1 The maximum concentration of ethers containing 5 or ...view more

Migrated from Progress Sheet (TC Comment) (2000-07-10): Updating of existing EN implementations of ISO standards (standing resolution); ++ Will go to VA.

Migrated from Progress Sheet (TC Comment) (2000-07-10): Revision of EN ISO 3675:1995

Migrated from Progress Sheet (TC Comment) (2000-07-10): Updating of existing EN implementations of ISO standards (standing resolution); ++ Will go to VA.

Migrated from Progress Sheet (TC Comment) (2000-07-10): Decision of BT to submit this ISO document to UAP procedure.

Gives a method for the determination, using an oscillation U-tube densitometer, of the density of crude petroleum and related products within the range 600 kg/m^3 to 1 100 kg/m^3 which can be handled as single-phase liquids at the test temperature and pressure.

Specifies a method for the laboratory determination. The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, reagents, sampling, procedure, expression of results, precision and test report. A centrifuge tube is shown in figure 1. The procedure for reading the volume of water and sediment is shown in figure 2. The precision of the method is shown in figure 3. The sample handling is described in annex A.

The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, solvent, calibration and recovery test, sampling, procedure, expression of results, precision and test report. The distillation apparatus is shown in figures 1 and 2. The precision of the method is shown in figure 3. The sample handling is described in annex A.

The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, solvent, calibration and recovery test, sampling, procedure, expression of results, precision and test report. The distillation apparatus is shown in figures 1 and 2. The precision of the method is shown in figure 3. The sample handling is described in annex A.

Specifies a method for the laboratory determination. The precision data of this procedure have only been determined for water contents up to 1 % (V/V). Includes principle, apparatus, reagents, sampling, procedure, expression of results, precision and test report. A centrifuge tube is shown in figure 1. The procedure for reading the volume of water and sediment is shown in figure 2. The precision of the method is shown in figure 3. The sample handling is described in annex A.

This European Standard describes a method for the determination of the boiling range distribution of petroleum products by capillary gas chromatography using flame ionisation detection. The standard is applicable to crude oils. The boiling range distribution and recovery to C100 or C120 can be determined.
Two procedures are described: single and dual analysis mode. The basis of each is the calculation procedure as described in Annex A.
NOTE 1   This standard does not purport to address all of th...view more