25.100.20 - Milling tools

This document specifies the dimensions for interchangeability between milling cutters with tenon drive and the cutter seating of cutter arbors. It is applicable only to milling cutters of the metric series. It gives the interchangeability dimensions for: — the milling cutters; — the cutter seating on the arbor; — the cutter retaining screw on the cutter arbor.

This European Standard specifies the determination of the maximum speed for given eccentricity at clamping devices for the shank strength of milling tools with cylindrical and taper shank. It also specifies the marking of the tool. Bore mounted tools which are mounted on an arbor shall be considered as a shank mounted tool.

This document specifies all hazards arising from the use of tools for woodworking machines, and describes the methods for the elimination or reduction of these hazards by tool design and by the provision of information. This document deals with milling tools (bore mounted, shank mounted), integrated tools and circular saw blades.

Livelink Error .chickletImage { behavior: url('/isostdsupport/pngbehavior.htc'); } Livelink Error: Error opening item. [Sorry, the item you requested could not be accessed. Either it does not exist or you do not have permission to access it. If you were sent a link to this item, please contact the sender for assistance.] Livelink ® Version 9.5.0, Copyright © 1995-2005 Open Text Inc. All rights reserved.

ISO 12197:2016 specifies the dimensions of milling cutters intended for manufacturing woodruff keyseats in accordance with ISO 3912. Two types of woodruff keyseat cutters with cylindrical shank are specified: - woodruff keyseat cutters with cylindrical shank, in accordance with ISO 3338‑1; - woodruff keyseat cutters with flatted cylindrical shank, in accordance with ISO 3338‑2.

ISO 2584:2016 specifies the dimensions of metric series cylindrical cutters with plain bore and key drive, intended for fitting to cutter arbors. It is applicable to solid cutters and also to interlocking cutters. Solid cutters are made either with straight teeth or with helicoidal teeth angled to the right or left; interlocking cutters are always made with straight or helicodial teeth angled to the left and right alternately. The range of outside diameters of these cutters is taken from ISO 523...view more

ISO 240:2016 specifies the dimensions for interchangeability between the cutter and the arbor or mandrel, i.e. the diameter of the bore and the arbor or mandrel and elements of the drive, whether by keying or tenon. It applies to all types of milling cutters mounted on cutter arbors or mandrels.

ISO 1641-1:2016 specifies the general dimensions of the following milling cutters with plain cylindrical, flatted cylindrical and threaded shanks: - end mills, flat-ended or ball-nosed: standard series and long series; - slot drills : short series and standard series. The dimensional characteristics of cylindrical shanks are in accordance with ISO 3338‑1, ISO 3338‑2 and ISO 3338‑3. NOTE These same milling cutters with Morse taper shanks having a tapped hole are dealt with in ISO 1641‑2, those wi...view more

ISO 10145-2:2016 specifies the general dimensions of end mills with brazed helical hardmetal tips, with 7/24 taper shank. The following two types of end mills with 7/24 taper shank are specified: - end mills with 7/24 taper shank for manual changing; - end mills with 7/24 taper shank for automatic tool changers. ISO 10145-2:2016 applies to right-hand and left-hand end mills, irrespective of helix angle and number of flutes.

ISO 10145-1:2016 specifies the general dimensions of end mills with brazed helical hardmetal tips, with parallel shank. The following two types of end mills with parallel shank are specified: - end mills with plain parallel shank; - end mills with flatted parallel shank. ISO 10145-1:2016 applies to right-hand and left-hand end mills, irrespective of the helix angle and number of flutes.

ISO 6262-1:2013 specifies the dimensions of end mills with indexable inserts and flatted parallel shank according to ISO 3338-2.

ISO 6262-2:2013 specifies the dimensions of end mills with indexable inserts and Morse taper shank according to ISO 296

ISO 6986:2013 specifies the dimensions of side and face milling (slotting) cutters with indexable inserts. The shape and dimensions of the inserts are left to the discretion of the manufacturer.

ISO 7755-12:2013 specifies the main dimensions of the cutting part for hardmetal burrs of inverted cone shape and designated by the symbol N.

ISO 7755-11:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cone shape, with a pointed nose and designated by the symbol M.

ISO 7755-2:2013 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape and designated by the symbol A. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.

ISO 7755-8:2013 specifies the main dimensions of the cutting part for hardmetal burrs of flame shape and designated by the symbol H.

ISO 7755-4:2013 specifies the main dimensions of the cutting part for hardmetal burrs of spherical shape and designated by the symbol D.

ISO 7755-9:2013 the main dimensions of the cutting part for hardmetal burrs of 60° cone and 90° cone shape and designated by the symbols J and K.

ISO 7755-5:2013 specifies the main dimensions of the cutting part for hardmetal burrs of oval shape and designated by the symbol E.