ISO/TC 43/SC 1/WG 45 - Description and measurement of environmental noise (Revision of ISO 1996-series)
Caractérisation et mesurage du bruit de l'environnement (Révision de la série ISO 1996)
General Information
ISO 1996-2:2017 describes how sound pressure levels intended as a basis for assessing environmental noise limits or comparison of scenarios in spatial studies can be determined. Determination can be done by direct measurement and by extrapolation of measurement results by means of calculation. This document is primarily intended to be used outdoors but some guidance is given for indoor measurements as well. It is flexible and to a large extent, the user determines the measurement effort and, accordingly, the measurement uncertainty, which is determined and reported in each case. Thus, no limits for allowable maximum uncertainty are set up. Often, the measurement results are combined with calculations to correct for reference operating or propagation conditions different from those during the actual measurement. This document can be applied on all kinds of environmental noise sources, such as road and rail traffic noise, aircraft noise and industrial noise.
- Standard60 pagesEnglish languagesale 15% off
- Standard66 pagesEnglish languagesale 10% offe-Library read for1 day
ISO/PAS 20065:2016 describes a method for the objective determination of the audibility of tones in environmental noise. It is intended to augment the usual method for evaluation on the basis of aural impression, in particular, in cases in which there is no agreement on the degree of the audibility of tones. The method described can be used if the frequency of the tone being evaluated is equal to, or greater than, 50 Hz. In other cases, if the tone frequency is below 50 Hz, or if other types of noise (such as screeching) are to be captured, then this method cannot replace subjective evaluation. The method presented herein can be used in continuous measurement stations that work automatically.
- Technical specification33 pagesEnglish languagesale 15% off
- Technical specification33 pagesEnglish languagesale 15% off
- Technical specification33 pagesFrench languagesale 15% off
ISO 1996-1:2016 defines the basic quantities to be used for the description of noise in community environments and describes basic assessment procedures. It also specifies methods to assess environmental noise and gives guidance on predicting the potential annoyance response of a community to long-term exposure from various types of environmental noises. The sound sources can be separate or in various combinations. Application of the method to predict annoyance response is limited to areas where people reside and to related long-term land uses. Community response to noise can vary differently among sound sources that are observed to have the same acoustic levels. This part of ISO 1996 describes adjustments for sounds that have different characteristics. The term "rating level" is used to describe physical sound predictions or measurements to which one or more adjustments have been added. On the basis of these rating levels, the long-term community response can be estimated. The sounds are assessed either singly or in combination, allowing for consideration, when deemed necessary by responsible authorities, of the special characteristics of their impulsiveness, tonality, and low-frequency content, and for the different characteristics of road-traffic noise, other forms of transportation noise (such as aircraft noise), and industrial noise. ISO 1996-1:2016 does not specify limits for environmental noise. NOTE 1 In acoustics, several different physical measures describing sound can have their level expressed in decibels (e.g. sound pressure, maximum sound pressure, and equivalent continuous sound pressure). The levels corresponding to these physical measures normally will differ for the same sound. This often leads to confusion. Therefore, it is necessary to specify the underlying physical quantity (e.g. sound pressure level, maximum sound pressure level, and equivalent continuous sound pressure level). NOTE 2 In this part of ISO 1996, quantities are expressed as levels in decibels. However, some countries validly express the underlying physical quantity, such as maximum sound pressure, in pascal or sound exposure in pascal-squared seconds. NOTE 3 ISO 1996‑2 deals with the determination of sound pressure levels.
- Standard53 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard47 pagesEnglish languagesale 15% off
ISO 1996-2:2007 describes how sound pressure levels can be determined by direct measurement, by extrapolation of measurement results by means of calculation, or exclusively by calculation, intended as a basis for assessing environmental noise. Recommendations are given regarding preferable conditions for measurement or calculation to be applied in cases where other regulations do not apply. ISO 1996-2:2007 can be used to measure with any frequency weighting or in any frequency band. Guidance is given to evaluate the uncertainty of the result of a noise assessment.
- Standard40 pagesEnglish languagesale 15% off
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard45 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 1996-1:2003 defines the basic quantities to be used for the description of noise in community environments and describes basic assessment procedures. It also specifies methods to assess environmental noise and gives guidance on predicting the potential annoyance response of a community to long-term exposure from various types of environmental noises. The sound sources can be separate or in various combinations. Application of the method to predict annoyance response is limited to areas where people reside and to related long-term land uses. Community response to noise can vary differently among sound sources that are observed to have the same acoustic levels. ISO 1996-1 describes adjustments for sounds that have different characteristics. The term rating level is used to describe physical sound predictions or measurements to which one or more adjustments have been added. On the basis of these rating levels, the long-term community response can be estimated. The sounds are assessed either singly or in combination, allowing for consideration, when deemed necessary by responsible authorities, of the special characteristics of their impulsiveness, tonality and low-frequency content, and for the different characteristics of road traffic noise, other forms of transportation noise (such as aircraft noise) and industrial noise. ISO 1996-1 does not specify limits for environmental noise.
- Standard26 pagesEnglish languagesale 15% off
- Standard31 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard27 pagesFrench languagesale 15% off
- Standard – translation27 pagesSlovenian languagesale 10% offe-Library read for1 day
- Standard8 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off