ISO/TC 94/SC 14/WG 1 - General requirements

This document sets out guidance for the selection, use, care and maintenance of PPE designed to provide protection for firefighters while carrying out their duties. The PPE covered in this document is intended for firefighting personnel exposed to risks associated with but not necessarily limited to the following activities: — structural firefighting; — wildland firefighting; — incidents involving hazardous materials; — incidents involving motor vehicle; — urban search and rescue. The purpose of this document is to highlight the main areas that a Fire service needs to consider when providing PPE to its members. This document is a supplement to the information provided in the PPE standards or used in conjunction with them. Most paragraphs of the document contain bulletlists, these lists are provided for guidance only and they are not exhaustive.

This document provides a test method for evaluating the physiological impact of protective fabric ensembles and potentially protective clothing ensembles in a series of simulated activities (phases) under defined ambient conditions. This standard test method characterizes the essential properties of fabric assemblies of a representative garment or clothing ensemble for thermo-physiological assessment: — dry thermal insulation; — cooling properties during average metabolic activity and moisture management (dry and wet heat transfer); — drying behaviour. Default measurements are done on fabric samples representing the garment or protective clothing combination. Optionally and in addition to the standard test method, the same testing protocol can be applied to characterise more complex protective clothing ensembles including underwear, air layer and certain design features[1]. In addition, measurements on readymade garments are possible. This test method is intended to be used to measure and describe the behaviour of fabric assemblies of a garment or clothing ensemble in response to a simulated series of activities under controlled laboratory conditions, with the results used to optimize garment combinations and material selection. Furthermore, this document together ISO 18640-2, is intended to be used to describe the thermo-physiological impact of protective clothing but not the risk for heat stress under actual fire conditions. The results of this test can be used as elements of a risk assessment with respect to thermo-physiological load. [1] A study conducted by Empa (Swiss Federal Laboratories for Materials Science and Technology, Switzerland) showed good correlation between results of standard torso tests (without underwear and air layers on fabrics) to tests on fabrics with underwear, tests on fabrics with underwear and air layers and test on readymade garments (with underwear and with or without air layers) of the same material composition. Due to the added thermal insulation values of the additional layers direct comparison of results between different measurement configurations is not possible, however.

This document specifies a method for evaluating the thermo-physiological impact of protective fabric ensembles and potentially protective clothing ensembles in a simulated activity under defined relevant conditions for firefighters. This document is intended to be used to assess the thermo-physiological impact of protective fabric ensembles and potentially protective clothing ensembles but not the risk for heat stress due to actual fire conditions. The results of this test method can be used as elements of characterisation and comparison of thermo-physiological impact of various types of protective fabric ensembles and potentially protective clothing ensembles. Default measurements are undertaken on fabric samples representing the garment or protective clothing combination. Optionally and in addition to the standard test method, the same testing protocol can be applied to characterise protective clothing ensembles including underwear, air layers and certain design features[1]. In addition measurements on readymade garments are optionally possible. NOTE The presently used evaluation methods are only validated for structural firefighting garments. [1] A study conducted at Empa (Swiss Federal Laboratories for Materials Science and Technology, Switzerland) showed good correlation between results of standard torso tests (without both underwear and air layers on fabrics) to tests on fabrics with underwear, tests on fabrics with underwear and air layers and test on readymade garments (with underwear and with or without air layers) of the same material composition. Due to the different thermal insulation of the systems direct comparison of the results is not possible.

ISO/TR 19591:2018 contains a list of terms which are frequently used in the standardization of personal protective equipment worn by firefighters and definitions of these terms. The definitions are intended to support an unambiguous use of the terms listed.

ISO/TR 21808:2009 sets out guidance for the selection, use, care and maintenance of personal protective equipment (PPE) designed to provide protection for firefighters while carrying out their duties. The PPE covered in ISO/TR 21808:2009 is intended for firefighting personnel exposed to risks associated with, but not necessarily limited to, the following activities: structural firefighting; wildland firefighting; incidents involving hazardous materials; incidents involving motor vehicles; urban search and rescue; swift water rescue; emergency medical response; storm and flood recovery. The purpose of ISO/TR 21808:2009 is to highlight the main areas that an organization needs to consider when providing PPE to its members. Most paragraphs of the document contain bullet lists; these lists are provided for guidance only and they are not exhaustive.