ISO/TC 14 - Shafts for machinery and accessories
Standardization in the field of shafts for machines, their keys and keyways, splines and serrations and their accessories such as couplings, flanges, etc.
Arbres pour machines et accessoires
Normalisation dans le domaine des arbres pour machines, de leur clavetage, cannelures et dentelures et de leurs accessoires, tels que accouplements, brides, etc.
General Information
This document specifies geometry and inspection dimensions for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines. Limiting dimensions, tolerances, manufacturing errors and their effects on the fit between connecting coaxial spline elements are defined and tabulated. Linear dimensions are expressed in millimetres and angular dimensions in degrees. The specified diameters for external splines in the geometry tables and the values in the inspection dimension tables are only valid for fundamental deviation "h". For fundamental deviations other than "h", diameters and tooth thicknesses are calculated for external splines according to the formulae in ISO 4156-1 and inspection dimensions according to the formulae in ISO 4156-3.
- Standard374 pagesEnglish languagesale 15% off
- Standard374 pagesFrench languagesale 15% off
- Draft374 pagesEnglish languagesale 15% off
This document provides data, guidance and requirements for the inspection of straight (non-helical) side fitting cylindrical involute splines. Limiting dimensions, tolerances, manufacturing deviations and their effects on the fit between connecting coaxial spline elements are defined and tabulated. Linear dimensions are expressed in millimetres and angular dimensions in degrees.
- Standard47 pagesEnglish languagesale 15% off
- Standard48 pagesFrench languagesale 15% off
- Draft44 pagesEnglish languagesale 15% off
- Draft47 pagesFrench languagesale 15% off
This document provides the data and indications necessary for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines. Limiting dimensions, tolerances, manufacturing deviations and their effects on the fit between connecting coaxial spline elements are defined in the formulae and given in the tables. Unless otherwise specified, linear dimensions are expressed in millimetres and angular dimensions in degrees.
- Standard62 pagesEnglish languagesale 15% off
- Standard63 pagesFrench languagesale 15% off
- Draft62 pagesEnglish languagesale 15% off
- Draft62 pagesFrench languagesale 15% off
ISO 4156-3:2005 provides data and guidance for the inspection of straight (non-helical) side fitting cylindrical involute splines.
- Standard44 pagesEnglish languagesale 15% off
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard45 pagesFrench languagesale 15% off
ISO 4156-2:2005 specifies geometry and inspection dimensions for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines. The specified diameters for external splines in the geometry tables and the values in the inspection dimension tables are only valid for fundamental deviation h. For fundamental deviations other than h, diameters and tooth thicknesses are calculated for external splines according to the formulae in ISO 4156-1:2005 and inspection dimensions according to the formulae in ISO 4156-3:2005.
- Standard188 pagesEnglish languagesale 15% off
- Standard193 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard188 pagesFrench languagesale 15% off
ISO 4156-1:2005 provides the data and indications necessary for the design and manufacture of straight (non-helical) side-fitting cylindrical involute splines.
- Standard59 pagesEnglish languagesale 15% off
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard59 pagesFrench languagesale 15% off
Contains table indicating tolerances on holes and shafts as well as on symmetry, gives directions for gauging such as gauging conditions and gauging control, and specifies control methods and corresponding gauges.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard12 pagesFrench languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
Is intended for the general application to cylindrical shafts and shafts ends, and gives the relationship which should be observed between the diameter of shaft and the section of key. Steel with a tensile strength of 590 N/mm is defined as the material to be used.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
Is intended for the general application to cylindrical shafts and gives the relationship which should be observed between the diameter of shaft and the section of key. Steel with a tensile strength of 590 N/mm is defined as the material to be used.
- Standard2 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesFrench languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
Specifies four series in millimeters and five series in inches of shaft heights, indicating tolerances such as limit deviations and parallelism errors.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
Provides data (in 111 tables) and indications necessary for inspection as well as three methods of inspection by limit gauges.
- Standard142 pagesEnglish languagesale 15% off
- Amendment142 pagesEnglish languagesale 10% offe-Library read for1 day
Provides data and guidance for the design, manufacture and inspection of the involute splines. Limiting dimensions, tolerances and manufacturing errors are defined and tabulated. Linear and angular dimensions are expressed in mm and degrees, respectively.
- Standard139 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesEnglish languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
Also specifies the material of the keys, gives the relation which should be observed between the diameter of shaft and the section of key, and is of general application for cylindrical shaft ends. It is recommended that the values given be adhered to even for special applications. For normal taper keys and corresponding keyways refer to ISO/R 773.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
Also specifies the material of the keys, gives the relation which should be observed between the diameter of shaft and the section of key, and is of general application for cylindrical shaft ends. It is recommended that the values given be adhered to even for special applications. For normal taper keys and corresponding keyways refer to ISO/R 774.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
- Standardization document7 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard4 pagesEnglish languagesale 15% off
- Standardization document4 pagesEnglish languagesale 10% offe-Library read for1 day